SKU: 96600779797

HappyModel Crux3 1S Toothpick Drone

$107.10 $119.00
Save 10%
No.2 Bestseller on salfueradeti.es >

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 14 - Jul 19

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

HappyModel Crux3 1S Toothpick DroneFeatures: 40gram 1s brushless Toothpick drone AIO Flight controller with ELRS Receiver and 5. 8G VTX CADDX ANT Camera New 1202. 5 KV11500 brushless motor Recommend to use 1s 450mah 650mah 660mah 720mah battery Compatible with CaddxFPV Peanut and Insta360 GO2 Carrying Caddxfpv peanut Got 4. 5 minutes flying time with 1s 650mah battery Specifications: Brand Name: Happymodel Item Name: Crux3 1S ELRS Wheelbase: 115mm Size: 97mmx97mmx35mm (without

Features:

40gram 1s brushless Toothpick drone

AIO Flight controller with ELRS Receiver and 5.8G VTX

CADDX ANT Camera

New 1202.5 KV11500 brushless motor

Recommend to use 1s 450mah/650mah/660mah/720mah battery

Compatible with CaddxFPV Peanut and Insta360 GO2

Carrying Caddxfpv peanut Got 4.5 minutes flying time with 1s 650mah battery
 

 

Specifications:
Brand Name: Happymodel
Item Name: Crux3 1S ELRS
Wheelbase: 115mm
Size: 97mmx97mmx35mm (without propellers)
Weight: 40g(without battery)

 


Package includes:

Item Name

Qty

Crux3 Frame and canopy

1

ELRS F4 2G4 flight controller built-in SPI ExpressLRS 2.4G receiver

1

Happymodel EX1202.5 KV11500 brushless motor

4

Gemfan 75mm bi-blade Propellers(4cw+4ccw)

1

Caddx Ant 1200TVL Global WDR with OSD 2g Ultra Light Nano FPV Camera

1

5.8G 25mw~200mw 40ch vtx (Flight controller built-in)

1

Screw Driver

1

Propeller disassemble tool

1

3D Printed canopy for Insta360 GO2 and CaddxFPV Peanut

 

Happymodel Handbag

1
 

 

 

Motor

Mode: EX1202.5 KV11500
Configu-ration:9N12P
Stator Diamter:12mm
Stator Length:2.5mm
Shaft Diameter:Φ1.5mm
Motor Dimension(Dia.*Len):Φ14mm*14.5mm
Weight(g):4.4g
No.of Cells(Lipo):1S
 

Propellers

Gemfan 75mm

Center Thickness:5mm

Prop Diameter:75mm

Center Hole diameter:1.5mm

Pitch:0.9in
 

Flight controller

MCU:STM32F411CEU6 (100MHZ, 512K FLASH)
Sensor: MPU-6000(SPI connection)
Original whoop size compatible
Power supply: 1S battery input (DC 2.9V-4.35V)
Built-in 5A(each) Blheli_S 4in1 ESC Dshot600 ready
Built-in Betaflight OSD(SPI Control)
Built-in 5.8G VTX
Built-in SPI ExpressLRS 2.4GHz receiver

Built-in 5V 1A BECFlight controller

firmware target: CRAZYBEEF4SX1280
 

Onboard 4in1 ESC

MCU upgraded to EFM8BB21
Power supply: 1S LiPo/LiPo HV

Current: 5A continuous peak 6A (3 seconds)
Support BLHeliSuite programmable
Factory firmware: O_H_5_REV16_7.HEX
Default protocol: DSHOT300
 

Onboard SPI ExpressLRS 2.4GHz Receiver

Packet Rate option: 25Hz/50Hz/150Hz/250Hz/500Hz
RF Frequency: 2.4GHz

Antenna : SMD antenna
Telemetry output Power: <12dBm

Receiver protocol to flight controller:  CRSF

Could bind with All ExpressLRS 2.4GHz TX module , ExpressLRS firmware need 1.0.0 or latest
 

Onboard 5.8g VTX

Output power: 25mw~200mw switchable
Frequency: 40CH
Input voltage: 3.3V 5.5V
Current consumption: 300mA(type)
Frequency: 5.8GHz 5bands 40 channels
With Race band 

Smartaudio ready
 

Caddx ANT 1200tvl camera

Image Sensor: 1/3" CMOS Sensor

Horizontal Resolution: 1200 TVL

TV System: NTSC or PAL 

IMAGE: 16:9 or 4:3

Synchronization: Internal

Electronic Shutter: PAL: 1/50~100,000; NTSC: 1/60~100,000

S/N Ratio : >52dB (AGC OFF)

Video Output: CVBS

Lens: 1.8mm

Min. Illumination: [email protected]

Auto Gain Control: YES

BLC: YES

WDR: Global WDR

DNR: 3D DNR

Dimensions: 14*14mm(with bracket to 19*19mm)

Wide Power Input: DC 3.7-18V

Work Temperature: -20℃~+60℃

Weight: 2g (N.W.)
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 96600779797

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.8 ★★★★★
Based on 2075 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
J
Verified Purchase
Jenna Rose
Pawtucket, US
★★★★★ 5
Magic!!!
I am no tech expert but these little guys are magic! We had just put in a wall of built-ins and desperately wanted to hide our cable box behind a cabinet, but with it being infrared this would not work without these little repeaters! First off I just have to say that the Sewell customer service is off the charts. You actually get to speak to a real person right away, no annoying menu after menu trying to get help. They helped us so much when we hit a couple snags. Here are a couple things that I figured out that I hope will help others. First you can hide both of these little discs, they both come with tiny little eyes that can attach to your tv and cable box or whatever you are trying to use them for, and they are nearly invisible. Second, don’t get nervous when you plug them into the power outlet and the lights don’t come on, this is ok and they aren’t supposed to stay on, they kind of blink here and there, and only when you use your remote. Third, we have an Altice One cable box (not the mini, just a regular cable box) and it was impossible to find the eye to attach the emitter’s eye (Side note: we had to put the emitter disc on top of the cable box because we couldn’t fit the emitter disc pointing in front of cable box. The directions give you both options though and you can basically put it anywhere as long as the eyes attach). The phone trick did not work on this particular cable box. But after trying about a dozen different spots on the front of the box we finally got it to work by putting the eye right on where the digital clock numbers are. I put it basically right on top of the colon (:). Cable vision was no help with this so I hope this can save others from our frustration. After we found the eye everything came together and worked perfectly! No more do we need to keep the cabinet open to change channels… it’s a miracle!!! Hope these little guys work forever.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 22, 2022
A
Verified Purchase
Amazonian
Birmingham, US
★★★★★ 4
Good product, expensive price, poor adhesive
Premium packaging for a premium device. Useful for IR remote signal delivery with extra functions on the side. Price though is luxury for it’s use. Used this for a Logitech Harmony hub control of an non-smart electric fireplace. Setup is a breeze but only if you’re tech savvy. Highly recommend to watch the YouTube video for information on all it’s application. There a many other cheaper devices similar to this available on Amazon that I could have used for the same application. If you have a need for multiple control within the same vicinity of other devices, this may be more useful for you. However, if you plan on utilizing an IR repeater/extender for only a single device and would like to save some money, don’t buy this one. This device works quite well though. Have had no issues achieving the effect needed. Only four stars due to the poor adhesive on the emitter attachment. As stated earlier, I used this on an electric fireplace with a glass surface. I used the attachable emitter to the front glass sensor where the IR receiver was located on the fireplace. After only one day, the emitter attachment fell off even though I made sure the glass was thoroughly cleaned prior to adhering it. Otherwise a good product.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 8, 2019
J
Verified Purchase
James P. Karl
Phoenix, US
★★★★★ 5
Denon avr ir remote port works great with sewell products
I bought a new entertainment center with glass doors and wasn't getting good signal range with the door closed. Plus i couldnt get a good of line site, since this cabinet was shorter than the orginal, and the location for my avr was further to the left than before and now my line of sight to the receiver was blocked from other parts of the room due to high couch back. I tried a couple different cheap $10 devices that used stick on transmitters/receiver buttons but they were clumsy and didn't provide me a total solution for my room layout. Works fantastic with a denon x1800 receiver (and many other models). It works directly with the denon's ir remote port in the back of the avr port. The solution is actually quite simple. Plug a stereo 3.5 mm male to male plug in the denon ir port in the back of the avr and and the other end to the orange emitter box(puck). The pics are about the size of an oreo double stuff cookie Tuck the orange box/puck away whereever and plug the power in. The box doesn't need to seen or be pointed towards anything. It's location is only limited by the length of your stereo cable and access to AC power Put the blue box puck anywhere in the room where you have general line of sight to it from where you will be using your remote, and plug power in. In my case, its sitting on top of one of my tower speakers. From there it clears the back of the couch and can see from the family room, eat-in kitchen area, and the kitchen beyond. Done. I didn't need or use any of the included emitter or transmitter cables, though if you dont have a denon, or other brand avr with an ir port to plug into , or also want to hide the blue puck ( in which case attach the included sensor cable), you'll need them. But for denon users with an ir port, you just use the two pucks and their usb power adapters. Simple.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 17, 2026
T
Verified Purchase
Tjaltz316
Grantham, US
★★★★★ 1
Worked good then died at six months (Updated)
Worked good for a couple of months, then started to develop a lag between when you pressed a button on the remote, and when the TV would respond. If I moved the speaker blocking the TV’s IR receiver, and pointed the remote at it, it worked perfectly. Add the IR blaster back in and the delay returns. The delay kept getting longer and longer, sometimes 5 to 10 seconds. Then it just died. Would not pass any IR signals, even though the receiver and emitter both had power. Tried rebooting, changing communication channels to no avail. Out of Amazon return window. Manufacturer wants you do go through a troubleshooting process for warranty that is too complicated and time consuming. Customer Service Rep at Sewell send me a warranty replacement.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 21, 2025
J
Verified Purchase
Jack & Ann Kenny
San Leandro, US
★★★★★ 5
Nice Product and Customer Service
I ordered this BlastIR Wireless Pro IR Repeater from Sewell to replace a wired version of an IR repeater from another company. We have moved our TV on to a wall location and are in the process of hiding all the wiring out of sight behind walls and/or in a cabinet. We still have some wires to go, but this product has enabled us to eliminate the IR wiring all together. It's a real improvement in both looks and performance over the cheaper, wired version we originally tried. The BlasterIR's Receiver is the component that faces the room and receives the IR signal from our remote controls. It's small enough to fit in the space between our sound bar and the bottom of the TV. It's range is great for our room size (about 22' long and 18' wide) and picks up the remotes signal from a side angle that's almost parallel to the TV itself. The receiver is powered through one of the USB ports integrated into the TV (although the device itself supports either a USB or regular plug-in option). I haven't used them yet but Sewell appears to have provided a few options to help with affixing the IR devices in their final positions including some adhesive pads and a magnetic pad option as well. I'm still playing around with the permanent placement of the IR Blaster Emitter. It sits inside a closed cabinet and faces the concealed cable box receiver, router and DVR components. It retransmits the various IR signals it receives from the IR receiver by blasting that signal to anything it faces. I just placed it in the cabinet about 5" away from the devices I wanted to control, plugged it in and it worked with no other set up. So far the BlastIR is working seamlessly and with much better function response time than the cheaper IR version we'd tried at first. The lag time between when a button is pressed on the remote control and the action taking place on the device I'm communicating with is minimal. The emitter itself is plugged into an outlet on a surge protector powering the other in-cabinet devices, although it too could be powered via the provided USB connection if desired. As a note, we did experience a shipping issue during our ordering process. The order it self was processed quickly and shipped in a timely manner. However, there was an issue with our actual receipt of the product and the USPS who reported it delivered to our mailbox when in fact it had not been. Regardless, we reached out to Sewell directly and they quickly resolved the issue for us with no problems and in a timely manner. I would recommend both this IR Blaster Pro product as well as Sewell as a trusted company itself.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 8, 2021

recommand products

92-6949 TUBE
20.99
Cabot Health Dr Cabot Ultimate Gut Health 250g
40.18
Cometic 2023 KTM 125 SX Top End Gasket Kit
92.49
Vw sharan ECU bosh me 7.5 repair service
110.00
Vw sharan ECU motronic m3.8.5 repair service
110.00