Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 13 - Jul 18
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Pecan Bowl Blank P-473 3" x 8" x 6.2"Pecan Bowl Blank P 473 3" x 8" x 6. 2" 3. 1 lbs. This is an attractive half log bowl blank of Texas grown Pecan wood. Its color is a soft tan to peachy light brown color with subtle darker brown streaks of mineralization. The wood grain has a pleasant and gracefully flowing pattern. It has full and well attached bark on the back side. There are extensive tunnels of a wood borer in an interesting pattern. This feature will likely need epoxy
|
Pecan Bowl Blank P-473 3" x 8" x 6.2" 3.1 lbs. This is an attractive half-log bowl blank of Texas-grown Pecan wood. Its color is a soft tan to peachy light brown color with subtle darker-brown streaks of mineralization. The wood grain has a pleasant and gracefully flowing pattern. It has full and well-attached bark on the back side. There are extensive tunnels of a wood borer in an interesting pattern. This feature will likely need epoxy stabilization if you want to preserve it or highlight it in your finished turning. This half-log bowl blank should be suitable for a bowl of 6-8" in diameter and 3" deep. With the bark on the backside, you have the option of turning a conventional bowl or a "barky" natural-edge bowl. However, if you want a full bark edge on the "natural" rim, you will need to secure the bark with CA glue before and possibly during turning. This piece is GREEN to partially air-dried, meaning that it still retains a lot of its original moisture from when it was a living tree. Moisture content was 20% when measured in May, 2022. It has been well-sealed and is in the process of slowly drying. It was heat-treated to kill off any hungry critters that may have been burrowing inside. If you need a current moisture content, please message us and we'll check its status for you. This is a classic half-log blank, split through the center of the log. There is no pith present in the block. I'm taking plenty of photos of this piece, so please scroll down below the first 3 photos to see more. About the Tree This Texas-grown Pecan tree was harvested in Fresno Texas in December, 2021. It was in a residential neighborhood where it had been planted near a home that was built in the 1930s. Over the years, the small Pecan tree grew large, and it threatened the house. The homeowners reluctantly called their tree company to cut down the tree and stack the wood for us to recover. We're always happy to save wood from the firepit or city dump. Their trash is now yours to treasure! |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.5 ★★★★★
Based on 896 reviews
Sort
Product Reviews
★★★★★ 5
If pump doesn't seem to work
Size: For 85-300 HP, Size: For 85-300 HP
Hi....I apologize it took me a while to get back to you with my results. Here is what I discovered about the pump and will also apply to some of the other comments I read in the reviews with people not getting the pump to work:
1.) I removed the pump to check the proper direction of the impeller and it was correct as can be seen in the photo.
2.) I built a pump shaft attachement so that I could operate the pump with a power drill.
3.) I attached the water muff to the unit and tried to pump water.....it wouldn't do so. What I did see however was that even at high hose discharge and small leakage at the muff I could not fill the water cavity in the housing.
4.) I installed a strap around the muff and tightened it very tight and THEN at high hose pressure I was able to get the cavity to fill with water.
5.) At that point I activated the drill and was able to get the pump to actually pump water. I then removed the pump housing and removed the O-Ring that resides on top of the impeller, reassembled and it would not pump water. Since the O-Ring sits higher than the original does I wanted to make sure that it was necessary to have it in the pump.
6.) I reassembled the engine and kept the tight strap on the bottom and finally it pumped water into the engine.
My conclusion that you can reply to other buyers if they have a problem:
Do NOT underestimate 2 things....1.)the lack of ability of the pump to draw water up AND 2.)the fact that if the muff leaks it will NOT fill the cavity when common sense says it should. This was a 120hp Johnson. The engine bottom must be immersed fully or the muff must be very tight on the lower unit for the pump to function.
Please feel free to post this if you wish.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 12, 2024
★★★★★ 5
Exelente
Size: For 85-300 HP
Exelente
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 21, 2026
★★★★★ 5
Good as new
Size: Package Dimensions 6.02 x 4.02 x 2.05 inches
Fitment was great and works as it should. Good quality
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 19, 2025
★★★★★ 3
Incorrect motor listed. Far smaller impeller than what's in the 6 horse johnson.
Size: For 5.5HP 6HP 7.5HP
It seems to be of good quality. However it does not fit a 6 horse johnson as it states. Therefore it will not pump water or function for my purposes. It was a waste of money.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 15, 2025
★★★★★ 5
Good product
Worked for what I needed. Fit great and easy to install.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 24, 2026