Pay in installments of $49.88 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 20 - Jul 25
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Speed Engineering Rear Brake Cooling Set - E82 1 Series M (1M), E9x M3SPEED ENGINEERING GMBH Pure Engineering Made in Germany. Speed Engineering thinks new in their ideas, developments, designs and products. Speed Engineering's standard is the extremely high demands in motorsport, which is reflected in every work step, whether in motorsport or off the race track. PRODUCT INFORMATION Rear Duct On racing vehicles, Speed Engineering were able to determine that the inside of the brake disc (despite the brake upgrade) on the
SPEED ENGINEERING GMBH
Pure Engineering - Made in Germany. Speed Engineering thinks new in their ideas, developments, designs and products. Speed Engineering's standard is the extremely high demands in motorsport, which is reflected in every work step, whether in motorsport or off the race track.
PRODUCT INFORMATION
Rear Duct
On racing vehicles, Speed Engineering were able to determine that the inside of the brake disc (despite the brake upgrade) on the rear axle builds up extreme temperatures. Apart from the high temperature development, an extreme difference between the inner and outer side leads to an uneven wear pattern on the brake pads.
The Speed Engineering solution is a plug & play upgrade and does not require any adjustments to the vehicle, no installation of a hose, clamps or other accessories making a wear-free system. The air is routed directly to the inside of the brake disc via an air duct.
The Speed Engineering solution is a plug & play upgrade and does not require any adjustments to the vehicle, no installation of a hose, clamps or other accessories making a wear-free system. The air is routed directly to the inside of the brake disc via an air duct.
Important Information
Disassembly of the anchor plate is strongly recommended.
Suitable for E82 1 Series M (1M) Coupe, E90 M3 Sedan, E92 M3 Coupe and E93 M3 Convertible models.
Scope of delivery
- 1x Air Duct, Rear Axle, Left
- 1x Air Duct, Rear Axle, Right
Models
- 1 Series / E82 / E88 (2007-2013) / 1 Series M (1M)
- 3 Series / E90 / E91 / E92 / E93 (2005-2013) / M3
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.5 ★★★★★
Based on 15 reviews
Sort
Product Reviews
★★★★★ 5
Works great on 36mm filters
Size: 36 mm, Color: Red
Works great on gmc 3.0 diesel fuel filter
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 7, 2026
★★★★★ 5
Must need socket for doing oil changes
Size: 32 mm, Color: Red
This is exactly what i was looking for. Now it makes doing my oil changes much quicker to do.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 19, 2026
★★★★★ 5
Works great, do the double drain for best results
My 06 Altima (185k miles) had been burning massive amounts of oil (like 4 quarts every 800 miles) due to a leaking PCV valve hose that took forever for me to narrow down (months). So after getting that under control I figured I needed to decontaminate the poor engine.
When using this I idled my car to operating temp (about 8 minutes). Poured the bottle in, idled it for another 15 minutes. Drained the oil (black and thick). Put the plug back in, poured about 2.5qts of new oil in. Idled it for 10 minutes. Drained that (black but much thinner). Took the old filter off. Let both areas drain for 10 minutes. Put the plug back in, put the new filter on and filled with the 4.6qts of new oil my car calls for. Ran for a few minutes (like 2 with a few revs) and then let sit for 10 mins before checking the level.
When I checked my dipstick it was so clean I thought I had a leak because I couldn't see it on any of the crosshatch. I ended up having to go by touch to get the reading. This stuff is amazing.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 15, 2025
★★★★★ 5
Worked for me! Definitely recommend!
Used a whole can in my 2009 Civic 1.8L with 150k miles. I can honestly say, this helped remove a lot of sludge out of the engine. The oil came out with a water-like texture and super dark! Before taking out the oil filter, I added new lower cost oil to the engine and let the engine run for about 5 minutes to get that extra flush! You can definitely see all the extra sludge in the new oil!
Drained and refilled with new oil and filter. The engine definitely sounded quieter and smoother than before!
If you value your car, I would definitely recommend doing this flush on your higher mileage cars every 50k miles or so!
Definitely recommend this LiquiMoly product!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 11, 2025
★★★★★ 5
3rd Update! See review... Good stuff and works as advertised...
Update - 3rd oil change/flush. Engine oil draining from engine is waaaay cleaner than my first flush. Probably won't need to do a 4th time for several changes. I added Ceratec at this change and am amazed how much better the engine performs since my initial flush. Less clatter and very smooth idle. (Jeep 4.0 I6)
Update- 2nd change and used the flush again. About 7000 miles from first use. The oil was cleaner and less "gunky" as first time but oil was definitely dirtier than normal. Right away noticed off idle throttle response improved. Then on a drive I take regularly with a mountain pass and long downhill I noticed that even tho the jeep downshifted out of OD it took much less throttle to hold 65 up a long grade. On the downhill normally I would see 50-60 mpg max on the digital readout. This time. It went to 99 which to me indicates more vaccum below the throttle plate. My guess is the rings freed up a bit more than the first flush and highway mileage is up to 23+ where I would get 21 before. Nice!
Used in 2001 Jeep Grand Cherokee. 140k miles and a ticking lifter (common in the 4.0 - 6 cylinder...). Definitely cleaned sludge (oil filter very heavy!) and oil was dark when draining. Idles smoother, oil stays cleaner longer, slight oil pressure increase and runs cooler. The lifter still ticks but probably a cam lobe issue. Will use it after 7500 miles or 1 year. Will report back after next change.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 22, 2017