Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 15 - Jul 20
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
145-175 uF MFD 110-125 VAC 50/60 Hz Round Start Capacitor - Fits AC Condenser Fan, Electric Motor145 175 uF MFD 50 60 Hz 110 125 VAC Volts Round Start Capacitor Key Features Capacitance: 145 175 MFD (Microfarads) Voltage Rating: 110 125 Volts AC Frequency: 50 60 Hz Shape: Round Case Material: Moisture and oil resistant molded plastic or aluminum Terminals: 1 4 inch male quick connect terminals Operating Temperature Range: 40C to 65C ( 40F to 149F) Dimensions: 1 7 16 in Diameter x 2 3 4 in Height Replaces Cross Reference Part Numbers This
145-175 uF MFD 50/60 Hz 110-125 VAC Volts Round Start Capacitor
Key Features
- Capacitance: 145-175 MFD (Microfarads)
- Voltage Rating: 110-125 Volts AC
- Frequency: 50/60 Hz
- Shape: Round
- Case Material: Moisture and oil-resistant molded plastic or aluminum
- Terminals: 1/4 inch male quick-connect terminals
- Operating Temperature Range: -40°C to 65°C (-40°F to 149°F)
- Dimensions: 1-7/16 in Diameter x 2-3/4 in Height
Replaces / Cross-Reference Part Numbers
- This capacitor serves as a universal replacement for any start capacitor with matching specifications.
- Replaces parts from brands such as BMI, Appli Parts, and others sharing the same MFD, voltage rating, and physical size.
- Common model type: CD60
Compatibility & Fitment
- Designed for intermittent duty in AC motor starting circuits.
- Suitable for single-phase electric motors requiring a start capacitor for initial torque.
- Commonly used in well pumps, HVAC units, air compressors, refrigeration systems, and other motor-driven equipment.
- Verify physical dimensions to ensure a proper fit within existing mounting brackets or enclosures.
When to Replace
- Motor hums but fails to start or struggles to reach full speed.
- Circuit breaker trips upon motor startup.
- Capacitor shows physical damage, such as bulging, cracking, or leaking fluid.
- Capacitance measures outside the 145-175 MFD range when tested with a multimeter.
Installation Tips
- Disconnect all electrical power to the equipment before beginning installation.
- Safely discharge the old capacitor by shorting the terminals with a resistor or an insulated tool.
- Confirm the voltage rating of the new capacitor is equal to or greater than the original.
- Ensure the MFD (uf) range of the new capacitor matches the manufacturer's requirement for the motor.
- Note the wiring configuration before disconnecting the old capacitor to ensure correct installation.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.6 ★★★★★
Based on 1744 reviews
Sort
Product Reviews
★★★★★ 4
Large coverage
Size: 1 Pack (24" x 36")
Takes one smudge to dry car.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 29, 2026
★★★★★ 5
Magsafe car mount for a Tesla screen that is easy to adjust and holds the phone very well
Style: MagSafe Car Phone Holder, Style: MagSafe Car Phone Holder
I installed this mount on my 2018 Tesla Model 3 main display and it was easy to install - just loosen the wheels on the top and side clamp, put it in place and then tighten the clamps back down. There is a ball mount on the back which tightens as well that allows you to position and angle the phone mount so you can tilt it up or down or towards the driver. You can adjust the phone on the mount to where you want it - although the bar that holds the phone will hit the clamps in two spots so there are a couple of positions that don't work due to the design, but overall you can more or less put the phone where you want and and then tilt it any which way to you.
The magnet connection is very firm but the phone also detaches relatively easily. The clamps so far are holding well on the screen. I really don't have a lot of complaints - except maybe that there's a couple of positions that don't work. It works well, installs quickly and easily and seems to hold well in use. I've had no problems so ar.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 25, 2025
★★★★★ 4
Mostly reliable to use
Style: MagSafe Car Phone Holder
It's nice to use in my car to separate out different needs like looking up a specific route while moving and the navigation is going somewhere. The magnet is pretty strong and haven't had any issues with that. However, if you dont put it in the corner of the screen to secure it at a right angle, the flat way to secure it in the middle of the top edge is not reliable at all. The weight of the phone and the angle of the mount makes it really easy to fall off the screen no matter how tight you secure it down. Fell at least a handful of times. Just put it at the corners and you'll be just fine.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 29, 2025
★★★★★ 2
Does not fit the Cybertruck. Will slip off due to angled backplate.
Style: MagSafe Car Phone Holder, Style: MagSafe Car Phone Holder
It does not fit the Cybertruck well. Due to the angled monitor back, it will slide off. Check the video of what I mean. It is not flat like the Model 3 or Ys.
The mount should work fine on the Model 3 and Model Y and Newer Model S and X, but not on the Cybertruck and older vertical screen Model S and X.
The Magsafe that I received must of been broken. It completely fell apart. Everytime I put on phone on it, the Magsafe will completely come off stuck to my phone.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 30, 2025
★★★★★ 3
Looks good, installs easily but the arm jitters on the road
Style: MagSafe Car Phone Holder, Style: MagSafe Car Phone Holder
Super easy and intuitive to install on my Tesla model 3. Once installed, I think it will probably hold position indefinitely. You can install it so that it is in a very convenient position. my right hand index finger was able to touch the screen of my phone while maintaining contact with the handle, so that should give you an idea. The reason I took 2 stars off is the way the goose neck jitters when driving. I think perhaps it is too thin. I drove on normal paved road, and the shakes were noticeable. It didn’t fall off at any point, but it made me nervous that it might. The magnet didn’t feel that strong either. A lot of people own phones larger and heavier than mine (iPhone 12 mini), so I’m reluctant to recommend.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 26, 2025