Pay in installments of $1605.00 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 19 - Jul 24
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Power Conditioner, Voltage Regulator, & Battery Backup UPS For Thermo Fisher Scientific TSQ Quantis MD Series Mass SpectrometerThis system is designed to provide voltage regulation, surge suppression, and automatic emergency backup power specifically for the Thermo Fisher Scientific TSQ Quantis MD Series Mass Spectrometer. Software Loaded For Specific Instrument Operation The UPS is loaded with software settings that limit the voltage fluctuations to within the range specified within the instrument site preparation guide. Hardware Configuration For Specific Instrument
This system is designed to provide voltage regulation, surge suppression, and automatic emergency backup power specifically for the Thermo Fisher Scientific TSQ Quantis MD Series Mass Spectrometer.
Software Loaded For Specific Instrument Operation - The UPS is loaded with software settings that limit the voltage fluctuations to within the range specified within the instrument site preparation guide.
Hardware Configuration For Specific Instrument Operation - The UPS internal bypass wire is removed which prevents voltages outside the acceptable operating range specified in the site preparation guide of the instrument to be passed through to the instrument.
-
Cuts Utility/Electric Costs compared to other battery backup UPS systems.
-
Slashes Setup/Installation Costs by requiring only a single receptacle for the UPS to be plugged into for power. If you don't already have the required receptacle, it can be installed by an electrician in advance of receiving the UPS and typically costs a fraction of the cost that it would cost to normally hardwire the UPS into an electrical panel.
-
Reduces Setup Time as the system arrives on a mini pallet with ramp included, rolls off the pallet, plugs into your wall receptacle, has a single switch/breaker on the back, and an ON button on the front LCD. The pre-installed dual voltage output PDU (power distribution unit) has all of the most used receptacles in North America so equipment can simply be plugged in. Unpacking, setup, and power up can be done within 5-10 minutes with only a Phillips screwdriver to unscrew the pallet blocks.
-
Eliminates Down Time as short duration power outages, voltage inconsistencies, surges, and other power issues are isolated away from any equipment you attach to the output receptacles.
-
Prolongs Equipment Life as built in circuit protection and voltage regulation ensure only the correct operating voltage is provided to the instrument at all times. Our factory configures this variation of the battery backup UPS in power conditioning mode so the unit will NOT ever switch to bypass mode which would potentially expose the attached equipment to the power problems and improper voltages.
-
Multiple Device Support as up to 6,000 VA of power consumption can be handled by the UPS. The output PDU has multiple receptacles and 2 simultaneous voltage outputs that match each receptacle type.
- Plug And Play Functionality, rolls off the pallet ready to plug in and turn on.
- INPUT: NEMA L6-30P (Plug)
- 208, 220, 230, or 240 Volts Single Phase, 30 Amp Breaker
- OUTPUT:
- 8x NEMA 5-15/20R (Receptacles, 115 Volts)
*Fits Either NEMA 5-15P (Plug) Or NEMA 5-20P (Plug) - 1x NEMA L5-30R (Receptacle, Twist Lock, 115 Volts)
*Fits NEMA L5-30P (Plug, Twist Lock) - 2x NEMA L6-15R (Receptacle, Twist Lock, 230 Volts)
*Fits NEMA L6-15P (Plug, Twist Lock) - 1x NEMA L6-20R (Receptacle, Twist Lock, 230 Volts)
*Fits NEMA L6-20P (Plug, Twist Lock) - 4x NEMA 6-15/20R (Receptacles, 230 Volts)
*Fits Either NEMA 6-15P (Plug) Or NEMA 6-20P (Plug) - 1x NEMA L6-30R (Receptacle, Twist Lock, 230 Volts)
*Fits NEMA L6-30P (Plug, Twist Lock)
User Guides:
-Battery Backup Power 6KVA-10KVA 1.0 PF Advanced Digital Tower UPS User Guide
-Battery Backup Power SNMP Card Full User Guide.pdf
Spec Sheet/Cut Sheet:
-BBP 4.5-10KVA 1.0 PF Advanced Digital Tower Specification Sheet.pdf
Complete 5 Tier Power Protection System – Surge Protection, Real Time Power Conditioning With Voltage Regulation, Heavy Duty Isolation Transformer, Pure Sine Wave Output, & Always On Double Conversion Backup Power Technology.
Extreme Energy Savings - Saves up to $1,892.16 per year over older model 6 KVA UPS systems in annual electricity costs due to energy efficiency enhancements.
Multiple Backup Time Options:
| Model Number: | Description (Under Battery Options Drop Down): | Approximate Backup Time At Full Load: |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS | UPS With Internal Batteries Only (20 Batteries, 12 Volts, 9 Amp Hours Each) 2.16 KWH | 15 Minutes |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS-WEBPWC | UPS Plus 1 Extra External Battery Pack (80 Batteries, 12 Volts, 9 Amp Hours Each) 8.64 KWH | 1 Hour 0 Minutes |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS-W2EBPWC | UPS Plus 2 Extra External Battery Packs (140 Batteries, 12 Volts, 9 Amp Hours Each) 15.12 KWH | 1 Hour 45 Minutes |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS-W3EBPWC | UPS Plus 3 Extra External Battery Packs (200 Batteries, 12 Volts, 9 Amp Hours Each) 21.60 KWH | 2 Hours 31 Minutes |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS-W4EBPWC | UPS Plus 4 Extra External Battery Packs (260 Batteries, 12 Volts, 9 Amp Hours Each) 28.08 KWH | 3 Hours 16 Minutes |
| BBP-ADV-6K-L630P-115230PDU-TSQQUANTIS-W5EBPWC | UPS Plus 5 Extra External Battery Packs (320 Batteries, 12 Volts, 9 Amp Hours Each) 34.56 KWH |
4 Hours 1 Minutes |
*Note: The 6 kVA model now has 9 amp hour batteries installed instead pf the standard 7 amp hour batteries. This increases battery capacity and backup time by approximately 22%.
- 6000 VA (6 kVA) / 6,000 Watt (6 kW)
- N+1 And Parallel Operation Up To 24 kVA (4 Units In Series)
- Energy Efficient/High Efficiency UPS Mode
- LCD Status Measurements Include Voltage, Frequency, Load Level, Battery Level, Output Current, and Estimated Remaining Backup Time
- Tower With Casters
- Pure Sine Wave Clean Output To Operate And Maximize The Life Of Even The Most Sensitive Electronics
- Online (Double Conversion) - Highest Level Of Protection Available - Battery Power Always Engaged, No Switching Delay (Phase Locked To Input Power Source)
- Wide Frequency Input Range (44-66 Hz Auto Sensing) Allows For Generator Power To Be Used As A Primary Or Secondary Input Power Source (Using Automatic Transfer Switch Before UPS)
- Constant Voltage Regulation (±1%)
- Constant Frequency Regulation (±1 or ±3% Selectable)
- Factory Warranty: 3 Years On Electronics And 1 Year Warranty On Batteries
- Optional Extended Warranty: 5 Years On Electronics And 1 Year Warranty On Batteries
- Digital Signal Processing (DSP) Allows For Greater Reliability Over Older UPS Designs And Superior Electric Noise Filtration
- >0.99 Input Power Factor / 1.0 Output Power Factor (Line Mode) / High Efficiency Mode For Superior Efficiency And Power Savings
- UPS Weight (Excluding Optional External Battery Packs): 264 lbs.
- Dimensions (Inches): 9.5 X 26 X 20 (W x H x D)
- Operating Temperature: 32°-104° F
- Operating Humidity: 20%~95%, Non-Condensing
- Operating Elevation: 3,280 Feet Without De-Rating
- Cold Start Capable (Shipped With Cold Start Disabled, Will Enable Automatically After Receiving Power For The First Time After Shipping)
- cTUVus, cULus, and FCC Certified
- Includes Software For Windows Monitoring & Configuration
Replacement Batteries:
-Leoch DJW12-9.0 (Lead Acid), Leoch LP12-9.0 (Lead Acid), Betta Batteries 6-HCNFJ-7.2 (Lead Crystal), Or Battery Backup Power BBP-LIFEPO4-HDR-12V-7.2AH (Lithium Iron Phosphate)
Do you need a PDF quote or a custom emergency backup solution? Email us at [email protected].
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.1 ★★★★★
Based on 28 reviews
Sort
Product Reviews
★★★★★ 5
Bright
Color: 7*5in Cube LED Pod
Very bright, good quality
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 12, 2026
★★★★★ 5
Easy to install
Color: 4*2.5in Cube LED Pod
Definitely more than I expected. .. dang good product and easy to install
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 11, 2026
★★★★★ 4
Easy Install Onto Jeep JKU, No Switch Backlight or Mounting Holes, Great Customer Service
Color: 5in Cube LED Pod, Color: 5in Cube LED Pod
I installed the Auxbeam 5" 168W LED Cube Pods onto my Jeep JKU Anniversary Steel Bumper. It was an easy install with some YouTube videos to help me snake the cables into the cab.
The unused holes in the steel bumper were the perfect size to fit the mounting bolts on the pod lights, and there was plenty of room to reach under the top edge of the bumper to install the nuts with some Loctite.
To snake the provided cable through the firewall, I had to remove the installed socket. This was easy to do by simply recessing the retainer clip on each pin, taking a picture of the wired connector before releasing the wires so I knew how to reassemble, snaking the connectorless cable through the firewall into the cab where the pins were then reinserted and locked into the connector. I dressed the cable by zip tie to the existing wire harness at the top of the engine bay. In the cab, I pulled the side panel from the dash (driver's side) and made a small hole for the cable in the panel. After cleaning the dash with alcohol, the adhesive-backed switch seems to hold nicely in place.
The lights were very bright and did a great job of illuminating the front and sides of the trail ahead of me.
No backlight on the switch, which is a necessity, and I dont understand why that feature is not present.
Also, there is no through hole to mount as the adhesive back won't stay attached, so the lack of a mounting hole is a big negative as well.
5 Month UPDATE: One of the lights got water inside. I noticed two screws that hold the glass cover were loose on the bottom of both sides. The other light also had the same loose screws but no water under the glass. I contacted Auxbeam, and they replaced the entire set in 2 days. Very awesome customer service.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 25, 2023
★★★★★ 5
Brightness and quality
Color: 4*2.5in Cube LED Pod
Got this for my 2024 Crosstrek. Got this one specifically due to its functionality that I wanted, quality for the price and it looks great especially DRL. I leave the Amber cover on most of the time. If you want the DRL to be on while the car is on, you can do that but it has to be rewired which I did. Love the brightness. I’ve been having this on my Crosstrek for a few months now and have no issues.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 3, 2026
★★★★★ 5
Bright lights
Color: 4*2.5in Cube LED Pod
Installed these on my Bronco as ditch lights. Very bright light and I like that you can have them be white or put the cover on them for and amber light look. Took about 30 minutes to install and wire to the upfitter switches. They shoot a wide angle covering your blind spots on dark roads. I got these to replace a three inch ditch light. They're made from heavy duty metal and stand up to the extreme weather. I like them so much that I purchased the seven inch lights and install them on the front bumper. For what they cost it was a price that I couldn't pass up. I highly recommend these lights.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 17, 2026