Pay in installments of $46.30 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 27 - Aug 1
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
PSS Shaft Seal 1-¼" Shaft 2-½" TubePSS Shaft Seal 1 1 4" Shaft 2 1 2" Tube Shaft Diameter: 1 1 4" Stern Tube Diameter (D): 2 1 2" to 2 5 8" Total Length (A): 7. 38" Total Length (compressed) (Compressed A): 6. 38" Rotor Diameter (B): 2. 875" Carbon Cuff Diameter (C): 2. 5" Stern Cuff Length (E): 1. 5" The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders yards. The PSS
PSS Shaft Seal 1-1/4" Shaft 2-1/2" TubeShaft Diameter: 1-1/4"
Stern Tube Diameter (D): 2-1/2" to 2-5/8"
Total Length (A): 7.38"
Total Length (compressed) (Compressed A): 6.38"
Rotor Diameter (B): 2.875"
Carbon Cuff Diameter (C): 2.5"
Stern Cuff Length (E): 1.5"
The PSS Shaft Seal is the number one selling marine mechanical seal worldwide and is installed as standard equipment by many of the worlds most reputable boat builders / yards. The PSS Shaft Seal is also recognized as the premiere retrofit (aftermarket) seal on the world market. Certified by Bureau Veritas, ABS & Rina: Boat builders / yards recognize the advantages and value of installing the PSS as it eliminates the maintenance, constant adjustment & cost associated with traditional packing type glands. Aside from these benefits, the PSS Shaft Seal helps to eliminate water in the bilge (100% water tight) & wear to the propeller shaft. The PSS Shaft Seal can be easily retrofitted and is available for shafts ranging from 3/4" (20mm) to 6" (150mm).
The PSS Shaft Seal is a mechanical face seal that is created between the flat surfaces of the rotating stainless steel rotor and the stationary carbon flange. The stationary carbon flange is attached to the vessels stern tube with hose clamps and the carbon flange is attached to the front side of the bellows with hose clamps. The stainless steel rotor is fit on the shaft in front of the carbon flange. The stainless steel rotor is used to compress the bellows before the collar is secured to the shaft with set-screws. This compression (pre-load) maintains contact between the faces and allows the PSS to compensate for the thrust from the propeller. The carbon flange is bored larger than the shaft diameter allowing it to "float" around the shaft and thus compensate for most misalignment and vibration problems. The stainless steel collar is sealed to the shaft by two o-rings that are recessed into the bore of the collar. These o-rings rotate with the shaft and stainless steel rotor and do not experience wear during operation.
**As with any rubber hose below waterline, the PSS bellows must be inspected on a regular basis for any sign of wear, aging or chemical deterioration. PYI suggests as preventative maintenance that the PSS bellow be replaced in six year intervals. During bellows replacement it is recommended the o-rings & set screws in the stainless steel rotor also be replaced."
Bellows may need to be more frequently inspected in an environment where non-sealed batteries emit sulfuric acid. Sulfuric acid vapor will accelerate rubber deterioration, as will an ozonater.
The Maintenance Kit includes the items you need to properly maintain your PSS Shaft Seal. Included in the kit is one (1) PSS bellow, two (2) O-rings, five (5) set screws, four (4) new hose clamps and an allen key.
Manufacturer : PSS Shaft Seal
Manufacturer Part No : 02-114-212
UPC : 839662007160
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.6 ★★★★★
Based on 22 reviews
Sort
Product Reviews
★★★★★ 5
Quality
Quality item. Using a butcher block on top to make a desk.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 13, 2026
★★★★★ 5
I love it!!!
Size: M Desk Unfinished 3/4-in and 1/2-in
Easy to assemble, all the pieces were in the box. I set everything out to be sure. Instructions were easy and clear, took about 10 min to put together.
Seems to be quality pipe, strong stable build even at just hand tight. When I put the desk top on it was already level so bonus there.
This kit is a great value, before I found the M desk I was looking on Pinterest for pipe leg designs thinking a trip to the hardware store and I could make it for cheaper, which was not the case. I 100% will recommend, and will purchase again.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2020
★★★★★ 5
Real steel pipe
Size: O Desk Unfinished 3/4-in and 1/2-in
This pipe table leg set was great. It's real steel pipe like from the hardware store. It does have a layer of oil on it so that must be stripped using dawn or some other degreaser before handleing and painting. It is also offset in the middle bar so if you use it as a desk you get more leg clearance. I used it as a table base so I bought matching middle braces to set the middle support in the center of the table. Once together it looks great. I highly recommend getting this if you want a good quality pipe base.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 11, 2023
★★★★★ 5
Price / Quality - Office Desk - Perfect
Size: H Desk Unfinished 3/4-in and 1/2-in
Purchased two sets to create a custom L shaped desk for the office. Placed a pine stained top. Perfect to handle a monitor, multiple laptops, normal office equipment. Extra benefit is the cross piece at the bottom as a foot rest. Very sturdy while sitting on carpet. Compared to normal pipe material purchased in large box store -- could not have asked for a better product for the price. Looking at other products for additional projects for around the house for the product and vendor. - Highly Recommend.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 27, 2021
★★★★★ 4
Fantastic style, good stability, customizable finish, and great customer service
Size: M Desk Unfinished 3/4-in and 1/2-in
Put this together in about April 2020 right about the crazy lockdown/quarantine/work-from-home timeframe. I knew that I wanted a simple hardwood desk with no drawers or stuff below the top. I have an ergonomic keyboard tray that I have attached to all my work desks for many years now, and it was too long for my old home desk, which was also made of MDF and was falling apart. Boo.
Enter this kit plus a butcher block top from the big box store. This kit went together easily. I had lost the instructions but a quick email to the JS Supplies company, and they hooked me up. By the time they sent it, I had actually figured out the part that was puzzling, which was what the all-thread pieces were for (the couplers between the elbows and the flanges on the top side).
I degreased all the parts with a simple Simple Green-type solution diluted in a 5 gallon bucket. I then sprayed the pieces with a satin nitrocellulose laqcuer (Minwax brand that I got from the home improvement big box). Worked great. I thought about doing a sealed rust finish using a science project volcano--vinegar and baking soda for a quick layer of rust on the outside--but I decided against it, as I wasn't sure of how stable the final product would be, even after a clear spray finish. The satin nitro finish looks great without even looking like a finish. I also coated the pieces with paste wax after the finish dried, just for good measure.
The one thing that is a bit disappointing is the stability... WITH MY TOP, mind you.I should be clear that the top that I'm using is a 1-3/4" thick monster piece of birch butcher block that is 60" x 30". I'm guessing that it's 40-50 pounds? Maybe more. This is probably WAY more weight than this leg set is made for. I also have the aforementioned keyboard tray that sticks out (torque equals force times lever arm) and causes even more torque. I get some shaking with the top with this setup. I have the desk on carpet; I was concerned that maybe the carpet and pad were not giving enough stability with the feet, so I made some plywood platforms for the feet. I also carefully leveled the feet to make sure it wasn't just uneven legs that was causing the instability. Still shakes no matter what I tried.
I think it's just that I have such a heavy top--more than this thing is spec'd for. That's totally fine, and I don't want to knock off a bunch of stars for that. I leave these comments more as a "don't do what I did" thing. Just be advised that you need to limit the weight of the top to something reasonable.
The design of one upright on each side of the desk with a pipe coupler in between is probably the weak spot with my heavy desktop; I'm thinking of either adding tension on either side (with some threaded rod and turnbuckles) or some extra supports with something like the Steel-Tek pieces from Lowe's.
Overall, I'm very satisfied with the product and the company!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 23, 2020