SKU: 10364797577

SpeedyBee F405 V4 BLS 60A 30x30 FC&ESC Stack

$107.99 $119.99
Save 10%
No.2 Bestseller on salfueradeti.es >

Pay in installments of $30.00 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 25 - Aug 30

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

SpeedyBee F405 V4 BLS 60A 30x30 FC&ESC StackSpecifications Product Name SpeedyBee F405 V4 30x30 Flight Controller MCU STM32F405 IMU(Gyro) ICM42688P USB Port Type Type C Barometer Built in OSD Chip AT7456E chip BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4) WIFI Not supported DJI Air Unit Connection Way Two ways supported: 6 pin connector or direct soldering. 6 pin DJI Air Unit Plug Supported. Completely compatible with

Specifications
Product Name SpeedyBee F405 V4 30x30 Flight Controller
MCU STM32F405
IMU(Gyro) ICM42688P
USB Port Type Type-C
Barometer Built-in
OSD Chip AT7456E chip
BLE Bluetooth Supported. Used for Flight Controller configuration (MSP should be enabled with Baud rate 115200 on UART4)
WIFI Not supported
DJI Air Unit Connection Way Two ways supported: 6-pin connector or direct soldering.
6-pin DJI Air Unit Plug Supported. Completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Blackbox MicroSD Card Slot *Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported (Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format. So, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. 
Current Sensor Input Supported. For SpeedyBee BLS 60A ESC, please set scale = 400 and Offset = 0.
Power Input 3S - 6S Lipo(Through G, BAT pins/pads from the 8-pin connector or 8-pads on the bottom side)
5V Output 9 groups of 5V output, four +5V pads and 1 BZ+ pad( used for Buzzer) on front side, and 4x LED 5V pads. The total current load is 3A.
9V Output 2 groups of 9V output, one +9V pad on front side and other included in a connector on bottom side. The total current load is 3A.
3.3V Output Supported. Designed for 3.3V-input receivers. Up to 500mA current load.
4.5V Output Supported. Designed for receiver and GPS module even when the FC is powered through the USB port. Up to 1A current load.
ESC Signal M1 - M4 on bottom side and M5-M8 on front side.
UART 6 sets(UART1, UART2, UART3, UART4(Dedicated for Bluetooth connection)), UART5 (Dedicated for ESC telemetry),UART6
ESC Telemetry UART R5
I2C Supported. SDA & SCL pads on front side. Used for magnetometer, sonar, etc.
Traditional Betaflight LED Pad Supported. 5V, G and LED pads on bottom of the front side. Used for WS2812 LED controlled by Betaflight firmware.
Buzzer BZ+ and BZ- pad used for 5V Buzzer
BOOT Button Supported.
[A]. Press and hold BOOT button and power the FC on at the same time will force the FC to enter DFU mode, this is for firmware flashing when the FC gets bricked.
[B]. When the FC is powered on and in standby mode, the BOOT button can be used to controller the LED strips connected to LED1-LED4 connectors on the bottom side. By default, short-press the BOOT button to cycle the LED displaying mode. Long-press the BOOT button to switch between SpeedyBee-LED mode and BF-LED mode. Under BF-LED mode, all the LED1-LED4 strips will be controlled by Betaflight firmware.
RSSI Input Supported. Named as RS on the front side.
Smart Port / F.Port Not supported
Supported Flight Controller Firmware BetaFlight(Default), INAV
Firmware Target Name SPEEDYBEEF405V4
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 41.6(L) x 39.4(W) x 7.8(H)mm
Weight 10.5g
Product Name SpeedyBee BLS 60A 30x30 4-in-1 ESC
Firmware BLHeli_S J-H-50
PC Configurator Download Link https://esc-configurator.com/
Continuous Current 60A * 4
Burst Current 80A(10 sec)
TVS Protective diode Yes
External Capacitor 1000uF Low ESR Capacitor(In the package)
ESC Protocol DSHOT300/600
Power Input 3-6S LiPo
Power Output VBAT
Current Sensor Support (Scale=400 Offset=0)
ESC Telemetry Not supported
Mounting 30.5 x 30.5mm( 4mm hole diameter)
Dimension 45.6(L) * 44(W) *8mm(H)
Weight 23.5g
 
$75.99 for a Bluetooth 60A Stack?
That's ridiculous
I know right? With only $75.99, you will get an STM32F405 FC (better than F411), onboard 4-level battery life indicator, 4GB Blackbox SD card slot for your flight logs, 4 groups of LED strip pads, complete with a DJI plug for your digital quad, and built-in Bluetooth for wireless configuration on the SpeedyBee app. Don’t forget about the powerful 60A 4-in-1 ESC, built with aluminum alloy heat sink + TVS protective diode + high-quality SMD filtering capacitors + external 1000uF low ESR capacitor, everything is for durable build and smooth flight.
All of that for only $75.99! Top-shelf spec at a crazy low price, what are you waiting for?
* The DJI Air Unit plug is completely compatible with DJI O3/RunCam Link/Caddx Vista/DJI Air Unit V1, no wire is needed to be changed.
Configure your FC and ESC via Bluetooth!
With SpeedyBee app, turn your phone into an all-in-one FC configurator and tune your quad anytime, anywhere. Enjoy wireless, fully configurable ESC experience with SpeedyBee app
ESC upgraded to 60A with heat sink.
The PCB design has been refined, with copper thickness increased from 2 to 3 ounces and enhanced MOSFET specifications. Continuous current now reaches 240A across all channels, peaking at 320A for 10 seconds. An added aluminum alloy heat sink ensures efficient MOSFET heat dissipation for stable ESC output. It delivers a genuine 60A output, primed for your baddest high-powered 6S motors.
ICM42688P Gyro and clean
power supply.
Featuring MaxLinear's esteemed LDO power chip, the gyroscope gets dedicated power, enhancing surge protection by 320%. A 100uF filtering tantalum capacitor shields gyro data from power interferences. This ensures precise flight responsiveness, letting you truly savor the joy of flying!
Forgot your LiPo checker?
Just look at the FC!
On the side of the flight controller, you will find a 4-level battery capacity indicator. As soon as you connect the battery, you can instantly see the battery level, saving you the hassle of needing to put on glasses to check the battery status.
SD card compatibility issue fixed!
The F405 V3 FC faced compatibility issues with certain microSD cards, with a few even occasionally affecting the stable OSD display. The improved F405 V4 flight controller, however, addresses these challenges. It reliably supports C4, C6, C10, and higher cards at 2k/4k logging rates.
BF/INAV can recognize up to 4GB of black box space. Once you clear the SD card, you can enjoy 1000+ flights. Experience black box freedom like never before!
Change motor directions wirelessly!
Are you still using a computer to change motor directions? With this stack, when you finish your build, connect to the SpeedyBee app, change the motor directions just in a few simple steps*. Then take off.
* To use this feature, please go to the App > Motors > Motor Direction Settings.
8 motors output for X8/Y6
You could use this stack to build your X8 drones and Y6 drones . Forget about crawling through your massive build just to plug in that USB cable. Just take out your phone to configure everything in the SpeedyBee app.
4 sets of LED pads with simple switching.
Need more visibility at night? Just solder up your LED strips* and blaze the darkest trail you can find. With just one tap on the BOOT button, you can cycle through all different LED presets** and pick the one you love!
* LED strips could be purchased here
**Or long press the boot button to switch to Betaflight LED mode.
TVS Protective Diode + 20 Onboard Filtering Capacitors + 1000uF High-Capacity Electrolytic Capacitor = Upgraded ESC Protection
We've included a TVS diode that effectively absorbs voltage spikes during power-up and crash events. The board features 20 high-quality SMD filtering and energy storage capacitors. These, along with the standard 1000uF high-frequency, low-ESR electrolytic capacitor, effectively filter out signal interference from the power supply to the flight controller's gyroscope, ensuring smoother flight performance.
And packaged with more useful features.
● Built-in barometer for accurate height calculation
● SD card slot can support up to 4GB Blackbox data*
● Dedicated DJI Air Unit connector for a quick digital build
● 5V & 9V Dual BECs now upgraded to both 3A output
● 4 x UARTs for your receiver + VTX + camera + GPS
● Power your GPS with a USB cable - no battery needed,
No extra heat, no worries
● 22mm cutouts for FPV camera in your tight build
*Betaflight firmware requires the type of the microSD card to be either Standard (SDSC) or High capacity (SDHC) under 32GB, so extended capacity cards (SDXC) are not supported(Many high-speed U3 cards are SDXC). Also the microSD card MUST be formatted with the FAT16 or FAT32 (recommended) format, you could use any SD card less than 32GB, but the Betaflight can only recognize 4GB maximum. We suggest you use this 3rd party formatting tool and choose 'Overwrite format' then format your card. Also check out here for the recommended SD cards or buy the tested cards from our store.
 
 
 
 
 
 
 
 
 
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 10364797577

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 26 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
S
Verified Purchase
Sarah Mason
Birmingham, US
★★★★★ 5
If you were looking for a sign to buy this, here it is
Color: A) Small 2.5" Ball
If you are looking for a ball that can stand up next to a heavy, aggressive chewer.. this is a good choice. Our Pitbull literally destroyed any and every toy that she gets with the exception of one kind of kong ball. She tore through the kong Frisbees, any kind of squeaker toy, and the wobble wag giggle ball (she usually always ends up destroying these but it takes a few weeks. Today she beat her record and had her brand new ball destroyed within the first 30 minutes of us taking it out of the box). But, this ball she has not been able to destroy. I'd like to believe that the Kong ball she has and this ball are made of the same material. Because they are the only balls she can't ruin. And it's not because of a lack of trying. We have watched her sit there and chew with a side of her mouth for an hour or more, trying to make some kind of indention or tear in it and it just never happened. She loves to chew this thing, chase this thing, sleep with this thing. I most certainly recommend this ball. If it is I'ah proof then it is most certainly, 100% a durable ball and worth every penny
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 7, 2026
M
Verified Purchase
Michael Campbell
Louisville, US
★★★★★ 5
Chew King Supreme Chew Toy
Color: B) Medium 3" Ball
So far, freaking amazing. This ball is awesome. I have a 90 lb American Bulldog. Like other reviews. Lot of " indestructible balls" lasted minimum time. Not this one. She even took it to bed with her I bought the 3 inch ball, not the 4 inch ball. The 3 inch ball works amazingly for a large Dog. Yes the 4 inch would be better. So in my opinion, either ball would be fine. As others also said. This ball keeps a active Dog busy for hours. Love to play catch. Love frozen peanut butter in it. One last thing. The price is amazing. I don't see needing to buy another, unless it is lost, because this is made to last. We couldn't be happier.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 10, 2026
K
Verified Purchase
Kelsey
Whiting, US
★★★★★ 5
Malinois proof
Color: B) Medium 3" Ball
So far this has held up great. My Malinois who has destroyed nearly every ball I’ve gotten her, this one has lasted over 3 weeks without a dent, compared to some that don’t even last a day lol. Although the medium size is a little too big for her liking she still plays with it. It’s very durable and I like the middle part for engagement as well. I would recommend if you have a dog who destroys every ball possible.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 8, 2026
T
Verified Purchase
TERRIE GILLAND
Draper, US
★★★★★ 5
Actually Durable
Color: B) Medium 3" Ball
One of the few "heavy duty" toys that my pittie hasn't destroyed after a couple of weeks. Most of them last two days. She's an absolute beast so I'm confident if she can't destroy it, few dogs can.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 28, 2026
C
Verified Purchase
Cody
Lowell, US
★★★★★ 1
Not for aggressive chewers!
Color: H) Infinity Ring, Color: H) Infinity Ring
Not for aggressive chewers! Done for in about two minutes. I unboxed this and tugged with my Mal for a but then let her have it. Within minutes she had chewed through it. Not worth the money.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 10, 2026

recommand products

Caroline'S Treasures Watercolor Princess Castle Wall Hook, Triple, Multicolor
36.59
RAW MINI DANISH *** WHOLESALE ***
109.00
Tresemme Color Revitalize Shampoo 170 ml
233.50
RAW DANISH *** WHOLESALE ***
157.30
Gucci bloom
19150.00