SKU: 75318507811

Lemon RX LM0086VP DSMP 7ch RX Telemetry, Stabilizer & Voltage Probe

Sale price$35.99 Regular price$39.99
Save 10%

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 15 - Jul 20

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Lemon RX LM0086VP DSMP 7ch RX Telemetry, Stabilizer & Voltage ProbeThe generation 2 DSMP 7 channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance. DSMX DSM2 compatible, 7 channel full range telemetry stabilizer with full telemetry features including a built in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both

The generation 2 DSMP 7-channel telemetry stabilizer is a complete redesign that provides the ultimate reliability, features and performance.

  • DSMX / DSM2 compatible, 7-channel full-range telemetry stabilizer with full telemetry features including a built-in barometer, altimeter, energy meter (Current, Voltage, mAh), and internal temperature sensor
  • High sensitivity gyro with proprietary stabilization algorithm ensures responsive airplane control for both electric and gasoline engine application
  • BEC1 and BEC2 dual inputs allow high-reliability operation while improving setup for high current drain performance servo
  • Built-in Delta, V-tail and Normal Wing mixer
  • Supports stabilization with separated channel dual aileron operation
  • Stabilization always-on feature
  • Real-time variable stabilization gain control on channel 8
  • All-channel failsafe
  • Firmware health monitoring software stack and ultra-low operational voltage (3.6V) ensure the highest hardware reliability
  • Generation 2 SDR stack ensures the fastest channel searching and advanced algorithm for signal recovery with ultra-low-latency experience
  • Antenna diversity improves the reliability of the wireless link
  • Satellite port for additional signal diversity
  • Gyro stabilization activation with either AUX2 or Gear channel
  • 3 potentiometers for individual gain tuning


User manual (See http://www.lemon-rx.com/manual Quick Reference Guide)

  • Reset stabilizer
  • Connect power
  • Hold F and B buttons (approximately 5 secs+) until all LED flashes randomly
  • Press the C button. Multiple LEDs flash a few times to complete the operation
  • Bind with bind plug
    • Insert bind plug on Channel 7
    • Connect power
  • Bind without bind plug
    • Connect power
    • Hold the B button until the red LED flashes
  • Bind with a satellite without a bind plug
    • Connect power
    • Hold the B button until the red LED flashes
    • Disconnect power
    • Plug the satellite wire connector into the stabilizer
    • Connect power
  • Failsafe
    • Connect power to the receiver and ensure the servos are working with the transmitter
    • Press the F button for 3 seconds until green changes from off to on and vice versa to change the failsafe setting. Channel value is saved as failsafe default at the time the green LED turns on.
    • Turn off the transmitter and wait 2 seconds to ensure the failsafe is activated accordingly by ensuring there is torque generated with finger-pushing the servo linkage if it was to be set. Vice versa.
  • Stabilization activation switch
    • Disconnect power
    • Insert bind plug to channel 5
    • Hold the C button
    • Connect power. Wait for about 1 second until the 6 LEDs flash.
    • Release the C button
    • Press C to make changes within 3 seconds. Green = CH7, Blue = CH5.
    • Wait for 3 seconds and remove the bind plug
  • Wing Mode and Dual Aileron
    • Disconnect power
    • Insert bind plug to channel 6
    • Hold the C button
    • Connect power. Wait for about 1 second until the 6 LEDs flash
    • Check the receiver label/user manual to understand the referred LEDs' operation
    • Release the C button
    • Observe which red LED is flashing and brief press C to select the required mode
    • Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
    • Wait for 3 seconds and remove the bind plug
    • Ensure transmitter mixing is set accordingly for dual aileron if stabilized dual aileron is to be configured.
  • Gyro direction
    • Check the receiver label/user manualto understand the referred LEDs' operation
    • Connect power and wait 1 second
    • Hold the C button and wait for about 1 second until the 6 LEDs flash
    • Release the C button
    • Observe which red LED is flashing and brief press C to select the required mode
    • Press C to toggle between settings. On means selected. Exit automatically in 5 seconds.
    • Wait for 3 seconds and remove the bind plug.
  • V/I sensor calibration
    • Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
    • Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
    • Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
    • Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
    • Press F or C button briefly
    • Observe 3 red LED flashes
    • Turn on the DC loading device by throttling the transmitter. Ensure 4A is drawing across the V/I sensor. Be careful with the motor spinning if it is to be used.
    • Press the B button to save and exit.
  • V/I probe calibration
    • Turn on the receiver and transmitter. The telemetry report page may optionally be checked during and after calibration.
    • Plug the V/I sensor. Make sure the required DC loading device such as a brushless motor with ESC as well as the current and voltage meter is connected.
    • Press the F and B buttons together at the same time for 2 seconds but no greater than 5 seconds
    • Observe 3 green LED flashes. Ensure 8.4V is provided to the V/I sensor.
    • Press F or C button briefly
    • Observe 3 red LED flashes
    • Press the B button to save and exit.
  • Gain setting
    • Adjust via the 3 dials or real-time master gain on channel 8 depending on the transmitter channel's availability.
  • View setting LEDs with all on
    • Press the C button briefly (no more than 2 seconds).


Lemon Rx products are tested to be compatible with Spektrum's DSMX and or DSM2 product (Spektrum, DSMX and DSM2 are the registered trademark of Horizon Hobby, Inc.).

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 75318507811

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 944 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
N
Verified Purchase
Nick N.
Louisville, US
★★★★★ 5
Good for welding leads
Size: 2 Gauge Cable, Color: 20 ft Black + 20 ft Red
Needed some welding lead extensions for a Miller maxstar clone typically running under 200 amps output. This cable fit the bill nicely.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 4, 2026
M
Verified Purchase
MD101
Grantham, US
★★★★★ 5
Nice and flexible wire
Size: 2 Gauge Cable, Color: 20 ft Black + 20 ft Red
This feels like nice wire and pure copper which is worth the extra cost. I was able to route this along the frame and around other wires with no issues, well at least not the fault of the wire. The insulation seemed to hold up with no issue as I pulled and re-routed it a few times. I haven't used the winch yet, so I can't say how the wire has held up under heavy load but I hope to soon so stay tuned. Have fun!
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on November 15, 2022
C
Verified Purchase
C
Dallas, US
★★★★★ 4
Very impressed with quality
Size: 2 Gauge Cable, Color: 20 ft Black
Quality, pliable and exactly what I was hoping for. I used it for a remote negative terminal kill switch. I have a C10 and Ran the cable from the negative terminal into the cab to a 12-volt kill switch and then back out of the cab to a ground on the frame. I would definitely recommend the cable and use it again.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 4, 2025
L
Verified Purchase
louiedog
Whiting, US
★★★★★ 5
Best deal out there for quality 2 gauge wire
Size: 2 Gauge Cable, Color: 20 ft Black
Great heavy duty wire at a great price
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 22, 2025
C
Verified Purchase
Cornelius Driedger
Louisville, US
★★★★★ 5
Gm
Size: 2 Gauge Cable, Color: 20 ft Black + 20 ft Red
Ok
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 25, 2026

recommand products