Pay in installments of $11.52 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 19 - Jul 24
For Your Every Summer RSVP, with Code: SUMMER15
Description
QDLASER Leadshine 3 Phase 3DM580s Stepper Motor Driver 18-50VDC 1.0-8.0AQDLASER Leadshine 3 Phase 3DM580s Stepper Motor Driver 18 50VDC 1. 0 8. 0A 1. Anti Resonance, provides optimum torque and nulls mid range instability 2. Motor self test and parameter auto setup technology, offers optimum responses with different motors 3. Microstep resolutions programmable, from 200 to 51,200 steps rev 4. Supply voltage up to +50 VDC 5. Output current programmable, from 1. 0A to 8. 0A 6. Pulse input frequency up to 500 KHz 7. TTL
1. Anti-Resonance, provides optimum torque and nulls mid-range instability
2. Motor self-test and parameter auto-setup technology, offers optimum responses with different motors
3. Microstep resolutions programmable, from 200 to 51,200 steps/rev
4. Supply voltage up to +50 VDC
5. Output current programmable, from 1.0A to 8.0A
6. Pulse input frequency up to 500 KHz
7. TTL compatible and optically isolated input
8. Automatic idle-current reduction
9. Suitable for 3/6 leads Three-phase motors
10. Support PUL/DIR and CW/CCW modes
11. Over-voltage, over-current, short-circuit protections
|
P1 Function |
3DM580 Details |
|
PUL+ |
Pulse signal: In single pulse (pulse/direction) mode, this input represents pulse signal, each rising or falling edge active (software configurable);4-5V when PUL-HIGH, 0-0.5V when PUL-LOW. In double pulse mode (pulse/pulse) , this input represents clockwise (CW) pulse,active both at high level and low level (software configurable). For reliable response, pulse width should be longer than 2.5 us. Series connect resistors for current-limiting when +12V or +24V used. The same as DIR and ENA signals. |
|
PUL- |
|
|
DIR+ |
DIR signal: In single-pulse mode, this signal has low/high voltage levels, representing two directions of motor rotation; in double-pulse mode (software configurable), this signal is counter-clock (CCW) pulse,active both at high level and low level (software configurable). For reliable motion response, DIR signal should be ahead of PUL signal by 5 us at least. 4-5V when DIR-HIGH, 0-0.5V when DIR-LOW. Please note that rotation direction is also related to motor-driver wiring match. Exchanging the connection of two wires for a coil to the driver will reverse motion direction. |
|
DIR- |
|
|
ENA+ |
Enable signal: This signal is used for enabling/disabling the driver. High level (NPN control signal, PNP and Differential control signals are on the contrary, namely Low level for enabling.) for enabling the driver and low level for disabling the driver. Usually left UNCONNECTED (ENABLED). |
|
ENA- |
|
P2 Function |
3DM580 Details |
|
GND |
Power Ground |
|
+Vdc |
Power supply, 18~50 VDC, Including voltage fluctuation and EMF voltage. |
|
U |
Motor phase U |
|
V |
Motor phase V |
|
W |
Motor phase W |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy