Luminex LU0100077-10-2S1 Gigacore 30I 10 gigabit AV Network Switch With 2X PSU

Luminex LU0100077-10-2S1 Gigacore 30I 10 gigabit AV Network Switch With 2X PSUGigaCore 30i comes fully optimized out of the box to be used with the most advanced AV protocols. Preconfigured Quality of Service (QoS), IGMP multicast, and PTPv2 settings will assure a responsive and extremely stable network environment for the most demanding time critical audio protocols like Dante, AES67, Q SYS, and many more. With up to 1000W of total PoE budget and PoE++ on every copper port, this GigaCore switch can drive almost any IP PTZ

GigaCore 30i comes fully optimized out of the box to be used with the most advanced AV protocols. Preconfigured Quality of Service (QoS), IGMP multicast, and PTPv2 settings will assure a responsive and extremely stable network environment for the most demanding time-critical audio protocols like Dante, AES67, Q-SYS, and many more.

With up to 1000W of total PoE budget and PoE++ on every copper port, this GigaCore switch can drive almost any IP PTZ camera or active loudspeaker on the market today.

GigaCore 30i is the ideal solution for AV networks in fixed installations, integration and touring for lighting, audio, and video. 

Features

• Most suitable applications: Fixed installations
• RLinkX (Link redundancy): Yes
• Groups (VLAN segmentation): Yes
• MultiLinkX (Link aggregation): Yes
• Profile manager: Yes
• Memory: Flash 1Gb RAM – 8Mb NOR flash 4Gb EMMC storage
• MAC address table: 16384 entries
• Address learning / Aging: Self-learning, Auto aging
• Switching throughput: 168Gbps
• Jumbo frames: MTU up to 12000
• IGMP support: Yes (V1/V2/V3)
• IGMP snooping: Yes, enabled by default
• Port sensing: Auto-negotiation
• Auto crossover: MDI / MDIX
• Auto-sensing: Full or Half Duplex (Gigabit is Full Duplex)

10Gb Connectivity

10Gb connectivity allows full network convergence of lighting control, audio, intercom, and compressed video.

PoE++

PoE++ implementation on every copper port allows you to connect any PoE device available today.

Today’s PoE standards (802.3af, 802.3at and 802.3bt) are all met. GigaCore 30i can directly drive almost any IP PTZ camera, network node or PoE powered loudspeaker on the market.

AV validated for real applications

GigaCore switches are fully validated in real-world applications with major brands in the AV industry for different protocols, including NDI, Dante, AVB/MILAN, AES67, ST-2110, IPMX, MA-Net, and many more. 

We don’t just approve against a protocol but actually test it. Because of real world application validation and interoperability testing, we understand the applications and make sure you can deploy our product with confidence.

Luminex support team really speaks your language and has a vast amount of AV knowledge built up, not just from talking protocols but mainly from working with you and living through your real application network challenges.

Robust yet silent design

A robust yet silent design allows you to use GigaCore in any AV environment.

Fans are speed controlled to have minimal noise impact and guarantee a long-life operation. This allows you to place the GigaCore in the most quiet environments like theaters and studio’s.

Araneo to manage and monitor the complete system

All GigaCore switches can be managed with a single network-wide tool: Araneo

Araneo’s online mode shows everything you need to know about the status of your GigaCore network. Data streams and topology are visualized as are the port status of every GigaCore.

Monitor your network with confidence and act before the show gets interrupted!

In offline mode, Araneo lets you plan the complete network topology and GigaCore settings in advance. Reducing network commissioning time to a mere click of a button.

Intuitive web UI

The built-in web UI allows you to adjust the settings in an intuitive way. Assigning Groups (VLANS) to ports, creating trunks or adjusting other port- and PoE settings can be done  on the fly and  the status page gives you an overview of the complete switch at a glance. The toolbox page allows management of profiles and lets you upgrade firmware easily.

Consistency in LED colours

Consistent Group (VLAN) colours in the web UI, in Araneo and on the front panel LED’s.

Specifications

• Connectivity
  • Ethernet connectivity: 24 x RJ45 connectors (1Gbps))
  • Fiber connectivity: 6 x SFP+ cages (10Gbps/1Gbps) (independent from other ports)
  • Ethernet port speed: 1Gbps
  • Serial: 1 x USB C
• Power
  • Power connectivity: 1 x IEC (14C) inlet for each PSU
  • Power input: 100-240VAC, 50-60Hz
  • Power consumption: Maximum 40W non PoE version Maximum 500W/1000W with PoE
  • Fuse: NA
  • Backup power input: 100-240VAC, 50-60Hz (through second hot swappable PSU)
  • Backup PoE power input: 100-240VAC, 50-60Hz (through second hot swappable PSU)
  • PoE: PoE ++ Optional (up to 1000W)
• Protocols
  • Supported protocols: Dante, RAVENNA/AES67, Ethersound, Q-SYS/Q-LAN, REAC, sACN, ArtNet, MANet2, HogNet, RTTrPL (BlackTraX), IEEE 802.1p CoS (Class of Service), DiffServ (DSCP), PoE (802.3af) (optional), PoE+ (optional), IEEE 1588 PTP V2
  • Sound protocol compliance: Yes (low jitter)
  • Ethernet compliance: IEEE 802.2, IEEE 802.3, IEEE 802.3u, IEEE 802.3x Flow Control, IEEE 802.3ab Gigabit Ethernet, IEEE 802.3af PoE, IEEE 802.3at PoE+, IEEE 802.3bt PoE++ 90W, IEEE 802.1p CoS, IEEE 802.1d Spanning Tree, IEEE 802.1w Rapid Spanning Tree, EEE 802.1s Multiple Spanning Tree, IEEE 802.1Q VLAN, IEEE 802.1ad LACP, IEEE 802.1ab LLDP, IEEE 1588-2008 PtPv2, IEEE 802.1 BA-2011, IEEE 802.1 Q-2011, IEEE 802.1 AS-2011
• Configuration
  • Display and jog: NA
  • Configuration: Through the built-in web server, Network-wide configuration through Araneo software
  • Status LEDs:
    • Global status LEDs: Device, power, PoE power, RLinkX, and mode
    • Port status LEDs: PoE, MultiLinkX, RLinkX, groups, link/activity, and port speed
    • Dark mode available
  • Colored RGB LEDs: Yes
• Physical
  • Mounting -  Rack
  • Enclosure -  Robust metal housing
  • Dimensions (W x D x H) -  482 x 309 x 44 mm (19" x 12.2" x 1.73")
  • Weight -  5.2 kg (with 2x 100W PSU inserted)
  • Environment
    • Operating temperature: 0 to +50 °C
    • Storage temperature: -10 to +70 °C
    • Humidity (non condensing): 5 to 95% RH
  • Noise level @1m:
    • Max 21,8dBA (Ambient: 0 – 30°C)
    • Max 37dBA (Ambient: 30 – 50°C)
    • Max 32,5dBA (PoE <550W, Ambient: 0 – 30°C)
    • Max 58dBA (PoE <550W, Ambient: 30 – 50°C)
    • Max 36dBA (PoE >550W, Ambient: 0 – 30°C)
    • Max 68dBA (PoE >550W, Ambient: 30 – 50°C)
  • BTU
    • 30i with 1x 100W PSU: Maximum BTU = 101.6 BTU/hr
    • 30i with 2x 100W PSU: Maximum BTU = 111.5 BTU/hr
    • 30i with 1x 550W PSU: Maximum BTU (Max PoE all ports) = 170.6 BTU/hr
  • 30i with 2x 550W PSU: Maximum BTU(Max PoE all ports) = 272.96 BTU/hr
  • Certificates/Approvals: cSGSus Mark (UL), CE Mark, UKCA Mark, CB certificate, RoHS
  • Standards: IEC 62368-1, UL 62368-1, CAN/CSA C22.2 No. 62368-1, EN 62368-1, FCC Part 15 CFR 47, CAN/ICES-003, EN 55032, EN 55024