SKU: 11423864549

2005-2010 Ford Focus Direct-Fit Catalytic Converter 5671196 Magnaflow

$307.35 $341.50
Save 10%
No.2 Bestseller on salfueradeti.es >

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Jul 13 - Jul 18

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

2005-2010 Ford Focus Direct-Fit Catalytic Converter 5671196 MagnaflowCatalytic Converter California Direct Fit Catalytic Converter Keep the check engine light off with MagnaFlow California Grade CARB Compliant Direct Fit Catalytic Converter 5671196. With features including free flowing mandrel bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state of the art metrology department

Catalytic Converter

California Direct-Fit Catalytic Converter

Keep the check engine light off with MagnaFlow California Grade CARB Compliant Direct-Fit Catalytic Converter 5671196. With features including free-flowing mandrel-bent tubing and highly corrosion resistant stainless steel construction, easily install this spun body converter yourself using the proper tools, no cutting or welding required. MagnaFlow's state-of-the-art metrology department uses the latest 3D scanning systems during research and development, so you can be confident that your new part will fit and function like the original equipment. By replicating the OE spun body design, the single laser fusion weld greatly reduces the possibility of a leak, and our compact, low-mass design also allows for greater thermal efficiency. This direct-fit catalytic converter is designed specifically for the 2005-2010 Ford Focus. Avoid potential exhaust leaks by using the included gaskets to get a proper seal. This replacement part is designed to meet or exceed California Air Resource Board requirements, and has undergone additional testing to comply with CARB guidelines to allow for legal use in California and CARB restricted states, for the listed vehicles.

Specs:

Air Tube Adaptable : NO
Air Tube Count : 0
Body Height : 4 IN
Body Length : 9.25 IN
Body Material : Stainless Steel
Body Shape : Round
Body Type : Spun
Body Width : 4 IN
Clamps Included : NO
Finish : Stainless Steel
Grade Type : Regular
Hangers Included : Yes
Heat Shield Attached : NO
Inlet Gasket Included : Yes
Inlet Inside Diameter : 2 IN
Inlet Mounting Hardware Included : Yes
Inlet Quantity : 1
Inlet Type : BOLT-ON
Outlet Gasket Included : NO
Outlet Inside Diameter : 2 IN
Outlet Mounting Hardware Included : NO
Outlet Quantity : 1
Outlet Type : Clamp-On
Overall Length : 19.25 IN
Sensor Port Count : 0
Series : California
Substrate Material : Ceramic
Title : MagnaFlow 2005-2010 Ford Focus California Grade CARB Compliant Direct-Fit Catalytic Converter
Tube Material : Stainless Steel
Type : Direct-Fit

Application:

  • 2005 - 2010 Ford Focus
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 11423864549

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.6 ★★★★★
Based on 280 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
N
Verified Purchase
Nc
Cuba, US
★★★★★ 4
Pretty good, take your time and install it well
Size: side table leg
Materials are pretty solid, but once assembled it’s not as sturdy as you would think it should be since the material itself was solid, i say give them a chance, everything out there that’s similar is way over priced
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 4, 2026
R
Verified Purchase
Roberta Mayes
Dallas, US
★★★★★ 5
Heavy duty legs for table.
Size: side table leg
Perfect legs for a table I am having made. I have an cottonwood slice. It's heavy and needed something substantial. These are perfect.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 25, 2026
R
R. Moheban
Dallas, US
★★★★★ 5
Robust pipe & fittings with a beautiful, smooth black finish
Size: side table leg
This set of pipe & fittings for use as low table legs is heavy duty and aesthetically pleasing. Especially when the pieces are handled, the tactile sensation is much nicer than with plumbing steel pipe because this product is beautifully finished smooth. The black pipes are quite smooth as well as the fittings. The pieces are all also pretty robust, though the wall thicknesses are less than in pipe for pressurized water systems. Of course that makes sense as this product does not need to hold fluid pressure. In my view they got the heaviness factor of this product just right; it's not as heavy or robust as black pipe used in natural gas supplies, but still robust and pretty heavy. Assembled, this product is absolutely stiff and unyielding for a solid table that could hold a man's weight easily. The feet utilize a brilliant scheme so that each foot can be independently adjusted for an uneven floor. Thus a level table on an uneven floor is easily accomplished. The feet simply extend the effective leg length by screwing counter-clockwise. To prevent any shifting at the threads adding some pipe compound or teflon tape may be advised. Even masking or duct tape might work as the idea is to just fill any gaps where male threads meet female threads. The four flanges at the tops of the legs provide a wide, solid surface for attaching the table top, with either hidden screws underneath or you could through-bolt a glass table top (provided you have the skill to drill glass!). I think this product would look great with a glass top. Assembly is quick and easy. The hardest part is drilling holes underneath the table top to accept screws. No pipe wrenches are needed as the pieces screw together by hand to an adequate tightness. If any doubt whether they are tightened enough have a strong person with grippy gloves finish. The "X" in the center attaches to the legs with a very clever machine screw system tightened with the included hex wrench. This is presumably because if tightened simply by screwing the fittings, the point of snugness would not likely be where the "T" fittings are exactly vertical. The maker has solved this problem so that you are assured that all legs will be in the perfect vertical position once everything is tight. The setup is also nice and rigid once tightened. This is a huge benefit of steel pipe projects; they are really solid. The black finish is clearly very durable, like a powder coat. It appears that it will provide excellent protection against rust. Coverage is complete; I found no dings or scratches anywhere on any piece. Overall this is a very well-designed product for function and aesthetics. Perfect for a beautifully renovated warehouse condo where an industrial vibe is desired in a rock-solid table that won't shift around. The smoothness of the pipe is top notch. I've used lots of pipe in projects, some of it actual water pipe and some decorative pipe such as this. I've never seen better quality decorative pipe as this maker put in the effort to finish it beautifully smooth. At currently $34.99 I find the price quite reasonable too.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 18, 2026
P
Verified Purchase
patricia
Boise, US
★★★★★ 3
the height is only 16"
Size: coffee table leg
The height is only 16". From the description it appears to be 24" wide and 24" high.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 2, 2026
C
CMC20
Grantham, US
★★★★★ 4
Good DIY Pipe Legs but Powder Coat Quality Lacks
Size: side table leg, Size: side table leg
These industrial style pipe legs make building a DIY end table easy and the kit saves a trip to the hardware store. The fittings go together normally and assembly is simple. Comes individually wrapped. My main issue is the powder coating looks and feels cheap and rubs off easily. The pipes already had marks from touching each other from unboxing. If you do not mind some wear on the finish over time this is a decent purchase. The metal at the hardware store will be thicker and more durable but will cost more. I’d recommend based on ease of having a kit and it being delivered saving me a trip.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 30, 2025

recommand products

Luiertas Jollein Moos Biscuit
49.99
Demon Heavy Duty Stock Length Axle - Polaris General 1000
112.50
Windshield Versa-Vent (Hard Poly) – Polaris General by Seizmik
210.00
Windshield Versa-Vent (Uncoated Poly) – Polaris General by Seizmik
150.00
Cotton Gadwal Saree
625.00