Hiblow HP-80 Septic Air Pump

Hiblow HP-80 Septic Air PumpKey Features Specs Warranty Documentation The Hiblow HP 80 features clean oil less air, boasts long operational life, offers extremely quiet operation, low vibration, low power consumption, and requires low starting current. If your Hiblow HP series pump wont turn on when first plugged in, it may have been bumped during shipping, which may have activated the safety slide switch to the position where it deactivates the electric motor. Please refer to

• Key Features
  
• Specs
• Warranty
• Documentation

• The Hiblow HP-80 features clean oil-less air, boasts long operational life, offers extremely quiet operation, low vibration, low power consumption, and requires low starting current.If your Hiblow HP series pump won’t turn on when first plugged in, it may have been bumped during shipping, which may have activated the safety slide switch to the position where it deactivates the electric motor. Please refer to the owner’s manual for instructions on how to reset the safety slide switch; you can find an electronic copy of the owner’s manual on the support tab of the Hiblow website.

  Hiblow pumps will only operate on alternating current (AC) in order for the shuttle rod to achieve the correct back and forth motion, which creates the necessary pressure or vacuum for proper functioning. If you must operate a Hiblow pump from a DC source, an inverter would be required.

  All Hiblow pumps can operate on either 50hz or 60hz. Do note that the pump’s performance will vary depending on the frequency. HIBLOW linear pumps are not dual voltage; please check the label for data on the correct voltage and only apply the indicate voltage to power the pump.

  For best performance and longest life, your Hiblow pump should be installed in a cool, dry location out of direct sunlight. A garage, shed, or crawlspace are all optimal options. If you must install the Hiblow pump in an outside location, be sure the pump receives sufficient ventilation—in order to achieve the maximum operating life, keep any additional heat exposure to a minimum.You (the customer) are responsible for making sure you are following all applicable laws and regulations in your area before replacing your septic air pump yourself.

• Liters Per Min (LPM)	80
  PSI (max continuous Operating Pressure)	3.6
  Noise Level (dBA) @ 1 Meter	36
  Current	1.6 A
  Rated Loading Pressure	2.13 psi
  Weight	15.4 lb
  Power Consumption	71 W
  Power Supply Frequency	60 Hz
  Condition	New
  Dimensions:	9.3'' L x 7.1'' W x 7.8'' H

  
  
  The maximum cfm is 4.2 cfm. This is at zero psi, so zero air would be going into the septic system. This is your cfm max airflow. 3.6 psi max continuous operating pressure you would want to pump on this Hiblow linear model.
  
  UL rated for outdoor no air pump housing is needed, and if one is used, it should be open on both ends for linear septic air pump.
  
  Pumps 80 LPM (Liters Per Minute) this is the optimal LPM, and psi is 2.13. This is also optimal.
  
  120 VAC, 60 Hz, 1.6A, 71 Watts three-prong plug if you need to hardwire it, you cut the plug.
  
  This does not affect the two-year warranty 36 dBA this is in a special test chamber in the real world they can barely be heard much quieter than rotary vane 
  
  Includes Rubber 90 with Hose Clamps Includes 1/8'' Brass Alarm Connection Fittings for an aerobic control panel.
  
  Hiblow HP80 linear air pump fits all 500 and 600 GPD Aerobic treatment units and is a compatible replacement Rebuild kits come as a complete repair kit with chamber block filter, safety screw, and diaphragm. You can also choose the linear diaphragm only.

• 2 Year Warranty Covering all Manufacturer Defects

  3 Year Warranty on Electrical Components ONLY

• Hiblow HP80 Septic Pump Documentation