SKU: 90054861730

PRO-TECH OGEE & FILLET BIT 1 3/8'X 9/16' 1/4'SHANK KP3701

Sale price$286.55 Regular price$318.39
Save 10%

Pay in installments of $79.60 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 27 - Sep 1

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

PRO-TECH OGEE & FILLET BIT 1 3/8'X 9/16' 1/4'SHANK KP3701Edge profile router bits Ogee & Fillet profile Carbide Tipped The ogee and fillet profile router bit is designed for creating decorative mouldings or edge profiles. This cutter allows one to shape a convex and concave shape. Adding to the depth of cut a fillet (bead) will be produced. An extra bead over the bottom corner is possible when replacing the guide bearing with a smaller size (KP100 3 8). This router bit has a 6. 35 mm shank (shaft) that will

Edge profile router bits
Ogee & Fillet profile

Carbide Tipped

The ogee and fillet profile router bit is designed for creating decorative mouldings or edge profiles. This cutter allows one to shape a convex and concave shape. Adding to the depth of cut a fillet (bead) will be produced.

 

An extra bead over the bottom corner is possible when replacing the guide bearing with a smaller size (KP100 3-8).

This router bit has a 6.35 mm shank (shaft) that will fit most small or large routers with the right collet. Please ensure that you select a router bit with a shank (shaft) size that will fit into your router collet.

PRO-TECH router bits are manufactured in Taiwan.

 

consider safety for your health and the people around you

General safety suggestions:

It is advisable to always have the following items nearby and in a good condition

  • Eye protection clean and scratch free
  • Hearing protection quality earmuffs
  • Dust masks discard old and dirty masks
  • Gloves for easy handling of material and hand protection
Wear Gloves
Eye Protection
Hearing Protection
Dust Mask

To use router bits safely (and to get the best results from your router), the router bits need to be installed properly into the router's collet. Improper installation of your bits can cause excessive chatter and could increase the likelihood that the bits will break when in use. 

Clean and sharp

First of all, before beginning any routing operation, check your bits to make sure that they are clean, relatively free of pitch, and most of all, sharp. If the bit is dull, chipped, is excessively burned or has any other defect, it should be sharpened or replaced before use. 

Correct collet and collet nut fit

Most router collets have a recess (groove) that needs to click into a circlip that resides inside the collet nut. Failing to ensure that the collet 'clicked' into the collet nut will cause you to struggle to remove the router bit after tightening. This could cause the collet to break or be removed by a technical repair centre.

 

Correct fit inside the collet

When installing the bit into the collet, do not tighten the collet with the bit 'seated.' Instead, insert the bit until the shank (bit shaft) reaches the bottom of the collet, then ease it out about 2 mm before tightening the collet.

When the bit is tightened, there should be no less than  2/3 's of the length of the shank in the collet. If your bit has a shank that is too short, then the bit should be replaced. 

 

Safety gear

There are a few other safety measures to keep in mind whenever you use your router. First of all, remember to always wear appropriate safety gear as indicated above.

Correct speed setting

Second, be sure to set your router to the proper speed for your router bit. Setting your router to an incorrect speed will not only affect the router's performance, but also can cause the bit to break much more easily and even cause bodily harm. The speed at which a router bit turns can be important. The typical router runs at about 22,000 rpm, which is fine for most bits. But as the diameter of the bit increases, you ll want to slow things down.

Also, before beginning any routing operation, be certain that you give the router's motor time to come up to full speed for the chosen setting. Beginning to cut before the bit is at full speed can give less than desired results. 

Observe the following at all times

  • Wear a protective face shield or Safety Glasses to prevent eye and face injury.
  • Wear ear plugs or ear muffs to protect your hearing.
  • Use a respirator or dust mask to give protection from dust particles. Wood dust may remain in the air for hours after using power tools.
  • Always read and follow router operator's manual instructions.
  • Make sure that router rpm's and the bit selected match.
  • Dress properly. Wear short sleeves, no loose fitting clothes, proper footwear and no jewellery. Tie back long hair.
  • Always be sure the router is unplugged before replacing bits and that the switch is off before connecting the router.
  • Be sure the router bit has completing stopped spinning before sitting the router down.
  • Be sure bits, clamps and attachments are secure before starting up.
  • Keep children, pets and visitors at a safe distance.
  • Be especially cautious when working small pieces.
  • Keep hands and fingers away from revolving bits and cutters.
  • Do not operate routers in moist or wet areas.
  • Always grip tool tightly and be prepared at start-up to resist the motor torque.
  • When using a router table, make sure on/off switch is easily accessible.
  • Learn the sound of your router and shut it off at any unfamiliar sounds or irregularities.
    Never start the router with the bit in contact with the material.
  • Always feed in the proper direction, against the direction of bit rotation.
  • Maintain equipment. Replace worn parts, discard worn-out bits and check router periodically. Clean parts with appropriate solvents.
  • Don't operate a tool if you are tired or under the influence of medication, drugs, alcohol or while smoking.
  • Check wood for nails, screws or loose knots before routing.
  • Keep your mind on your work, avoid distractions, work at a comfortable pace and stop before you get tired.

Do a dry run

  • Place the router on the final work surface and test you cut by moving the router over the whole are to cut with THE ROUTER SWITCHED OFF
  • You do not want to waste an expensive piece of wood
  • You do not want to start all over
  • Never met anyone with spare fingers - SAFETY
Part No. Shank dia. Cutting width Cutting Height
KP3701 1/4 inch 1 3/8 inch 9/16 inch
6.35 mm 34.9 mm 14.29 mm

 

Length of Shank: 32 mm
Replacement bearing part number: KP100 1-2

 

 



KP3701Router Bits > Profiles > Ogee / Fillet
Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 90054861730

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.6 ★★★★★
Based on 18 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
H
Verified Purchase
hngrdg
Phoenix, US
★★★★★ 5
Breathable, comfortable, warm
Color: Burgundy
Breathable during heavy exercise. Long enough to double up when used as a neck gaiter. Soft and comfortable. Warm.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 10, 2026
A
Verified Purchase
Amazon Customer
Chelsea, US
★★★★★ 4
Ehh
Color: Black, Color: Black
Eh. I mean, it was warm… but it trapped moisture from me breathing into it, so then it was like wet… which wasn’t ideal. Didn’t stay up on my nose super well. I had to tuck it into my goggles. Easy to wash. Decently soft. Feel like it wasn’t exactly worth the money I spent, but I know it is real wool, so that comes with a price tag. I don’t know…I really didn’t like the water / moisture getting trapped around my mouth and chin and what not. Just causing skin breakout issues. Helped cut the cold wind, but I feel like it could be better, or like there are better options out there maybe. Maybe not meant for snowboarding or exercising, so you’re not breathing as hard into it. Maybe it’s just meant for walking around with it around your neck. I don’t know.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 27, 2026
M
Verified Purchase
michael kincaid
Los Angeles, US
★★★★★ 5
Not very itchy, easy to put in your pocket and warm
Color: Black
I wore turtle fur for a long time and liked it except that it's too big to fit in my pocket. This wool product has really impressed me so far. It doesn't have a zero itch rating but it is very soft. It's surprisingly warm for its weight. Fits easily in my coat pockets. It's comfortable, fits well on both my neck and face as it has some stretch to it. It had a smell when I first opened the package but that went away after a couple of days. I wore it around my neck in 20F and was warm. I would say that using it as a face mask at that temperature would be pushing its limits. I find it to be a good balance between size and warmth for the Kentucky tri-state area in a mild winter. Because of it's size you can easily put a layer over it during extreme cold and it would be well worth the space it takes in your pocket
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 12, 2024
S
Verified Purchase
Samuel
Grantham, US
★★★★★ 5
Robbery
Color: Black
Very warm and light
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 8, 2026
D
Verified Purchase
David George
Birmingham, US
★★★★★ 3
Too Short
Color: Burgundy
I like the material and construction; it's soft and thick. It is warm and is effective at temperatures in the teens and winds around 30 mph. The thickness of the material helps prevent my breath from instantly condensing and moistening the fabric. I never got the "wet dog" smell wet wool is known for. Its fit is a little tight but not prohibitively so. The color matches that of the beanie. It's too sort to be considered versatile. In wind I had to choose between shielding my neck or my face. I HIGHLY recommend you not machine wash and dry. Hand wash it and let it dry naturally.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on February 27, 2026

recommand products