Glow In The Dark DTF Gang SheetsTransfers Ready for Press On Special Luminous Film Transfer Glow N The Dark Film Transfers are the newest in DTF technology. Our Glow N The Dark Film Transfers print your image on a special Luminous film making your design glow n the dark for approximately 4 10 hours based on the amount of light your design is exposed to. With superior attention to quality, you can relax knowing that your order will be printed to exceed the highest standards in the

Transfers | Ready for Press | On Special Luminous Film Transfer

Glow N The Dark Film Transfers are the newest in DTF technology. Our Glow N The Dark Film Transfers print your image on a special Luminous film making your design glow n the dark for approximately 4-10 hours based on the amount of light your design is exposed to. With superior attention to quality, you can relax knowing that your order will be printed to exceed the highest standards in the industry. Vivid, soft-feel transfers Professionally printed on commercial printers. No peeling, fading or cracking. Works on ALL fabric and ALL colors

• Make any design glow in the dark
• Similar application process to standard DTF
• Better hand-feel than vinyl
• Ultra-fine details with no weeding required
• Glow in the Dark transfers adhere to all fabric types in any color, including cotton, polyester, nylon, and rayon
• No pretreatment is required for colors
• Professional grade adhesive
• Create premium, glow-in-the-dark apparel at home. Perfect for concerts and costumes.
• Note: Your entire design will receive a layer of glow in the dark coating. Requires time to "charge" in a well-lit setting before glow effect will work. Light colors will glow more than dark colors.

This Is a cold Peel DTF Transfers****

Easy Application

• To ensure your DTF transfer looks professionally pressed every time, follow these five simple steps.

  1. No Need To Pre-Press Or Pre-Iron: Removing moisture is unnecessary. Only do a prepress if you so desire.
  2. Position Your Design: Take your time to line up your transfer in the desired location on your item. Normally, there is no need to use heat-resistant tape on flat heat presses to keep your design in place, however, it is highly recommended when pressing transfers onto hats or when using an iron to keep the transfer in place. You’ll get a feel for when this is needed. For more precise positioning, use DTF Alignment Ruler Set.
  3. Press: Press your transfer with medium pressure at 310°F / 155°C for 15 seconds. You cannot damage the transfer by pressing with more heat, pressure, or time -- within reason. However, too much heat can damage your garment, so test first and use parchment paper or a protective guard sheet to protect your garment from a direct iron.
  4. Let It Cool. Then Peel It: After pressing, let your transfer rest until it is cool to the touch (minimum of 15-30 seconds). To speed up the cooling process, use Fast Cool Peel Air Transfer Blower. Once cool, lift the transfer from one corner and gently peel back. We have a saying in the dojo, which is, don’t use your hands, use your EYES. This ensures every piece of your design is adhering to your item. If not, stop peeling, lay it back down, and troubleshoot as follows -- (1.) If some or all of the design does not transfer AND it was cool when peeling, it means there was not enough heat, pressure, or time. Press your transfer again with more pressure and time first (+5-10 seconds). (2.) If that doesn’t work, try 15°F heat increments until you find the sweet spot. You truly cannot damage the transfer by pressing multiple times.
  5. Final Press & Wash Instructions: Place the parchment paper included or a single layer of t-shirt material over the design and press again for 15 seconds to soften the design, increase durability, and remove shine. If you want a shiny finish, cover it with a protective guard sheet for the final press. When washing, flip the shirt inside out, wash on cold, and dry using low heat or hang.

• Image Guidelines

• The original image must be a minimum of 300 dpi and in PNG, SVG, or JPEG format.
• Note: enlarging a 300dpi image (i.e. from 3" to 9") and exporting it may cause pixelation and quality issues.
• Color shifts can occur when converting to CMYK for DTF printing.
• Do not mirror your image, and please use transparent or removed backgrounds (unless you want the background printed).
• We recommend a minimum of 7.5px/0.25" for small fonts or thin lines to ensure the ink and powder is applied properly.
  
• We print what we receive. Spelling, placement, sizing, and image quality will not be fixed by our team.

Recommended Equipment:

For the best results, we strongly recommend using a commercial heat press for DTF transfers.

Pre-Press Steps:

• Pre-press your garment for 5-10s to eliminate moisture and wrinkles.
• If aligning your design with a fold, do this before pre-pressing.

*Please note: If the image does not transfer completely when peeling, repress with the image in place for 5-10 seconds, let it cool again, and re-peel the film.

**Using parchment for post-press will produce a more matte design. Using Teflon for post-press will produce a glossier design.

Care Instructions: Turn the garment inside out. Machine wash cold. No bleach. No softener. Tumble dry low. Do not dry clean or iron

We stand behind the quality of the transfers we print for you. If you are not satisfied, 

• We’ll reprint your DTF transfers for free if there’s a defect with your order that includes the following:
  • Image quality issues when using a 300-DPI image
  • Adherence issues
  • Damage caused by shipping

Try our other DTF Transfers products!

Looking to brighten up your designs and make them stand out even more? check our specialty DTF Transfers

• Pearl DTF Transfers
• Glitter DTF Transfers
• Sublimation Transfers
• Glow in the Dark Transfers
• Reflective Transfers
• Gold DTF Transfers