DINITROL RUST CONVERTER MAZDA MX5 RUST PROOFING CAVITY WAX LITRES KIT DIN33

DINITROL RUST CONVERTER MAZDA MX5 RUST PROOFING CAVITY WAX LITRES KIT DIN33DINITROL ML was developed for use in closed cavities such as doors, frame parts and external hinges and gaps. The product can be used as corrosion protection for used cars, trucks, buses and other vehicles. BenefitsBrownExtremely PenetratingStops ongoing corrosionWater displacingOily, flexible filmWet in wet with bitumen vehicle Underbody coatingApplicationDINITROL ML is designed for application into closed cavities such as doors, frame members and

DINITROL ML was developed for use in closed cavities such as doors, frame parts and external hinges and gaps. The product can be used as corrosion protection for used cars, trucks, buses and other vehicles.
Benefits
Brown
Extremely Penetrating
Stops ongoing corrosion
Water displacing
Oily, flexible film
Wet in wet with bitumen vehicle Underbody coating
Application
DINITROL ML is designed for application into closed cavities such as doors, frame members and exterior joints and crevices. The product can be used for rust-proofing of second-hand cars, trucks, buses and other vehicles. Application temperature should be between 15 and 30°C.
Method of use
DINITROL ML is applied by spraying with manual or semi-automatic.
DINITROL application equipment, and is suitable for either air-mixed or airless spraying.
Pre-treatment Substrates
DINITROL ML is possible to apply on mois and corroded surfaces. For the best result, loose corrosion shall be removed before application.
Over-Coating / 2-Layer-Application
DINITROL ML can be over-applied with any of the DINITROL bitumen underbody coatings. For additional information, please consult DINOL GmbH.
Storage
The product shall be stored at 15 ? 30°C and the shelf life is then 2 years in unopened original packages.
Technical Data
Colour brown
Type of film oily, greasy
Density at 23°C 860 kg/m³
Viscosity at 23°C, (DIN 2) 60 seconds
Dry matter content 46% by weight
Flash point 40°C
Aromatic content in solvent < 1 %
Recommendes film thickness 10 ?m
Recommended film thickness wet 30 ?m
Drying time 1 hour
Heat resistance 80°C
Low temperature adhesion < - 40°C
Salt spray test > 96 hours
Penetration in 50 ?m wide gap > 70 mm
Effect on car paint none
Removability White Spirit
Available in 1 L Miniservice / 5L Pail / 20 L Pail
60 L Drum / 208 L Drum / Container

DINITROL 4941 / 4941 CAR is a long term protective product. The product leaves a firm, black film with short drying time and good adhesion and flexibility on all metal surfaces, rubber and plastic parts.
Benefits
OEM references
Robust universal film
Self-healing
Easily applied
Good abrasion resistance
Component protection
Applications
DINITROL 4941 / 4941 CAR is an underbody product or use in the treatment of vehicles during production, at import plants and in aftermarket applications. When applied to a clean, dry surface, it adheres to both painted surfaces and those coated with a layer of PVC or similar material. Zinc, rubber and plastics are completely unharmed by the product.
A clean and economic treatment on the line is assured by the products ease of application and high dry matter content. DINITROL 4941 / 4941 CAR is also designed for use on spare parts, machines and iron and steel structures in highly corrosive environments. DINITROL 4941 / 4941 CAR is also very suitable as an anticorrosive coating for transport and warehousing under extremely corrosive conditions.
Method of use
DINITROL 4941 / 4941 CAR can be applied by manual or automatic application equipment, airless or airmix.
Recommended application and product temperature is 15 ? 30°C.
Pre-treatment Substrates
DINITROL 4941 / 4941 CAR can be applied directly to clean, dry and corrosion free surfaces.
If corrosion is present, DINITROL ML or a DINITROL cavity wax shall be applied before.
Over-Coating / 2-Layer-Application
DINITROL 4941 / 4941 CAR can not be over-painted.
For additional information, please consult DINOL GmbH.
Technical Data
Colour - black
Type of film - hard, waxy
Density at 23°C - approx. 1100 kg/m³
Viscosity at 23°C - 800 mPas
Dry matter content - 69% by weight
Flash point - 36°C
Aromatic content in solvent - 0,5%
Recommended film thickness wet - 700 ?m
Recommended layer thickness - 300 ? 500 ?m
Drying time - 6 ? 12 Stunden through dry
Low temperature adhesion - -20°C
Removability - Hydrocarbon solvents
Heat resistance - 130°C
Salt spray resistance, 300 m - 1500 hours

DINITROL 4010 Corroheat leaves a hard, transparent film that is resistant to both alkali and acids and is heat resistant up to a temperature of 200°C. It has a tack-free and clean film which facilitates a visual inspection of metal surfaces, reading of labels and numbers etc.
BENEFITS
Engine protection
High temperature resistance
High adhesion
Long term protection
APPLICATIONS
The adhesion and flexibility on rubber and plastic parts at both low and high temperatures are very good. Appropriate parts to be treated with DINITROL 4010 Corroheat are engine compartments, engines and other parts which have to withstand high temperatures.
METHOD OF USE
DINITROL 4010 Corro heat should be applied on a clean, dry surface. High or low-pressure equipment can be used, airless or air mix. Application temperature between 15 to 30°C. Product hardness, flexibility and adhesion increase at higher drying temperatures.
PRE-TREATMENT
Substrates Surfaces shall be dry, clean and free from corrosion.
OVER-COATING
Normally not to be overpainted. For additional information, please consult DINOL GmbH.
STORAGE
The product should be stored at 15 to 30°C and the shelf life is then 2 years in unopened original packages
TECHNICAL DATA
Colour transparent beige
Type of film hard, waxy
Density at 23°C 890 kg/m³
Viscosity at 23°C, DIN 4 25 seconds
Dry matter content 47% by weight
Aromatic part in the solvent 0,5 %
Recommended film thickness wet 120 ?m
Recommended film thickness 40 ?m
Drying time 120 µm wet, 1 h with optimal ventilation
120 µm wet, 4-6 hours at RT 23°C 50% RH
Low temperature adhesiont -30°C
Effect on car paint none
Removability within 3 months Hydrocarbon solvents
Heat resistance
Short-term 200°C
Long-term 160°C
Salt spray test (drying 24 h, 80°C) 240 hrs 40 microns dry
500 hrs 80 mircrons dry
Available in 10 L Canister / 20 L Pail / 60 L Drum / 208 L Drum

DINITROL RC 900 is a rust converter based on organic chelate complex combined with epoxy resin. It actively converts the rust on the substrate into a stable organic iron complex. When the product dries, it forms an impenetrable barrier to further corrosion. DINITROL RC 900 penetrates about 7?10 times deeper into the rust than conventional rust conversion products and forms a dry and strong adhesive film that is suitable as a base for the lacquer structure and as a carrier for other corrosion protection products.
Benefits
Polymer film formed on converted rust
Deep effect
Easy application
Deep working properties
Overpaintable
Applications
DINITROL RC 900 is designed for use on oxidized iron parts.
Method of use
Remove rust, grease and dirt with a wire brush, sand paper or a sandblasting process. Rust and scale may only be visible as slight shading. In addition to rust, the steel must also be free from dust and grease. Carefully clean with acetone or lacquer thinner. Shake the spray can well. The product should be applied in several successive coats, at a distance of approx. 25 cm.
The metal temperature should not be below 10°C. The material is dust-dry after one hour, if necessary, a further coat can be applied.
Pre-treatment Substrates
DINITROL RC 900 should be applied to corroded surfaces. Loose rust must be removed before processing.
Over-Coating / 2-Layer-Application
DINITROL RC 900 can be overapplied with most DINITROL Corrosion Prevention products and with most common complete paint systems. For additional information, please consult DINOL GmbH.
Technical Data
Colour amber-coloured
Appearance solution
Film type hard
Density 0,9 g/cm3
Viscosity 118 cSt
Solids 16%
Recommended film thickness 130 µm
Yield ~ 60 g/m² per coat
Drying time 24 hours at 20°C
Storage time 10 years (between 15°C and 25°C)
Avaialable in 400 ml Spray

Kit contains:
2 x 1L Dinitrol ML Cavity Wax Aerosol
3 x 1L Dinitrol 4941 Underbody Wax Aerosol
2 x 500ml Dinitrol 4010 Clear High Temperature Wax Aerosol
1 x 400ml Dinitrol RC900 Rust Converter Aerosol
1 x SCHUTZ Gun
25 x 10mm Black Plugs
1 x CANGUN