Pay in installments of $52.50 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 23 - Jul 28
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Pedal Commander PC67 Bluetooth Throttle Response ControllerIf you need help choosing a Pedal Commander that best suits your vehicle, please contact us. Eliminates Delay Nowadays, vehicles are notorious for their delayed throttle response. Vehicles use a drive by wire system that monitors the position of the gas pedal to control the throttle electronically, similar to a dimmer switch. The problem with this setup is that the signal from the pedal has to first be sent the ECU, which in turn then sends the signal
If you need help choosing a Pedal Commander that best suits your vehicle, please contact us.
Eliminates Delay
Nowadays, vehicles are notorious for their delayed throttle response. Vehicles use a drive-by-wire system that monitors the position of the gas pedal to control the throttle electronically, similar to a dimmer switch. The problem with this setup is that the signal from the pedal has to first be sent the ECU, which in turn then sends the signal to the actuator motor that controls the throttle body itself. This delay is most noticeable when trying to speed up to merge with fast moving traffic or pass a slower moving car. However, the Pedal Commander Bluetooth Throttle Response Controller will eliminate that delayed throttled response, giving your vehicle a drastic night and day difference in performance.
Four Adjustable Control Modes
Unlike other throttle control devices that are either on or off, the Pedal Commander comes with 4 control modes: Eco, City, Sport and Sport +. Best of all, each mode has an additional 8 different levels of sensitivity which allows you to personally adjust each mode to your own personal driving style and needs. Switching between modes can be done manually on the Commander or can also be done using your smartphone (Pedal Commander App).
Compatible with Aftermarket Programmers
Can be used in conjunction with common aftermarket OBD-II programmers and/or monitors such as: SCT, Diablosport, Hypertech, Superchips, Bully Dog, and Edge.
2-Year Product Warranty
In the event you do receive a defective or malfunctioning device, we will replace it free of charge within 2 years of the original purchase date.
Easy Plug & Play Installation
Connects directly into the stock throttle position sensor found on the drive-by-wire gas pedal using an OEM style plug and play connector with no permanent modifications required. It is 100% reversible, making it warranty friendly.
Mode Features
Eco Mode: Will reduce engine response 50% slower than stock. Can help up to 20% savings in fuel.
City Mode: Increased response for active traffic. Suggested for daily drive
Sport Mode: High performance response for spirited driving.
Sport+ Mode: Extreme response. Strongly suggested for Track & Race use.
This kit includes |
Compatibility |
|
(1) Throttle Response Controller. (1) Installation Instructions. (1) Mounting Bracket. (2) Zip Ties. (1) Alcohol Swab. (1) Mounting Velcro. |
Specific Renault vehicles |
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.9 ★★★★★
Based on 13 reviews
Sort
Product Reviews
★★★★★ 5
Superior Design!
Size: 6 Pairs / 12 pcs
Delivery was lightning fast.
I tried a pack of two pairs of these banana jacks as a sample to see if these would meet my needs. The design of these plugs is superior. The design was exactly what I wanted because the speaker wire is secured with TWO set screws. Then I ordered an additional six pairs of plugs to hook up my subwoofer to my amp and speakers.
(I feed the audio output from the amp to the sub. The sub has a crossover that keeps the low frequencies and sends the mid and treble frequencies to my bookshelf speakers.)
I love the security of two set screws on each plug and love the barrel that screws on AFTER the wire is secured by the set screws. Most banana plugs have a hole through the shaft of the plug that receives the stripped wire. Then the barrel cover is screwed down to secure the wire in the plug. This design compresses the speaker wire but eventually the cap loses it grip and allows the connection between the wire and the plug to become loose. Then the transfer of the audio signal becomes poor and the speakers sound bad. Every month or two I needed to check all the banana plugs and re-tighten many of them for the best performance. The two set screws eliminate this problem. The set screws are quite small and take a little extra care in installation. You will need a small flat blade screwdriver to tighten them. I used the 1/8" flat blade driver from a set of jewelers screwdrivers.
These well made plugs are a bit pricier that many of the banana plugs available but certainly not the priciest plugs available. For me, the slightly higher price was more than offset by the security of the wire within the plug.
I'm not thrilled with the extra tight fit of the tip on the plugs into the jacks. It took a lot of effort to insert the in the jack. Actually I "greased" the pins (very sparingly) with with non-corrosion, conductive paste (Ox-Gard, No-Corrode, etc. Do NOT use any other grease.) Next time I'll use pliers to compress the pin.
My only quibbles are that the spring pins that go into the jack are very tight and that the plugs are only sold in quantities of two pairs or 12 pairs.
I recommend these banana plugs for all who are using the banana plugs and jacks for hooking up your speakers. It's a very convenient way of connecting speakers if your speakers and amplifier have the banana jack as part of the binding post. Further, it's much safer to use banana plugs since the possibility of shorting your amplifier with a stray strand of wire is practically zero. Easy Five Stars.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 13, 2018
★★★★★ 5
Top banana
Size: 5 Pairs / 10 pcs
Theses banana plugs are hight quality non magnetic. Banana plugs easy to usexand very high quality sound different because of the better connection and quality.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 24, 2026
★★★★★ 5
Very easy to use
Size: 12 Pairs / 24 pcs
I have an Onkyo audio/video receiver along with an Emotiva amplifier. Both have speaker "post" terminals which will accept banana plugs, OR I can connect the speaker wires by unscrewing the posts, poke the speaker wires into the terminals and then tighten the posts. The problem with poking the wires into the terminals and tightening the posts vs using banana plugs is that there is a risk of the wires touching the metal on the back of the chassis or touching other speaker wires, causing a short if one is not careful. With banana plugs, they simply plug into the back/top of the posts, eliminating the rsick of a short circuit. They can also be unplugged very easily if needed. Banana plugs are DEFINITELY the preferred way to connect speakers to an receiver or amplifier if they have post-style terminals.
These particular banana plugs came in a package of 12 I believe. They were very reasonably priced, and simple to connect to the end of the speaker wires. Simply unscrew the banana plugs, use a small, standard jewelry screwdriver and loosen both of the set screws, insert the speaker wire, then tighten the set screws, and then screw the banana plug back together.
The plugs have either a red band which would typically be used for your "Right" speakers, or a black band which would typically be used for the "left" speakers. The banana plugs insert into the top or front of the speaker terminal posts on the amp and receiver. They fit VERY snug, and so I did have to apply just a little bit of pressure in order to insert them into the posts, but once plugged in, rest assured they're not going anywhere. They are snug.
I highly recommend these.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 2, 2025
★★★★★ 5
Thick wires
Size: 4/0AWG, Color: 10ft Black + 10ft Red
Heavy duty for my solar set up. These wires are thick. I've never used such thick wires for anything. Now I know why they're so expensive. There was some weight to these wire too. The diameter is larger than a dime. These are some serious wire.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 25, 2025
★★★★★ 5
Monster cable
Size: 4/0AWG, Color: 3ft Black + 3ft Red
Well I now know what 4/0 or 0000 cable is. Huge but very easy to handle or bend to shape.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on January 13, 2026