Pay in installments of $14.74 with
,
and
Shipping Estimate
USA
- USA
- CAN
- USA
- CAN
Ships within 48 hours · Estimated delivery Jul 27 - Aug 1
Promo Codes Available:
For Your Every Summer RSVP, with Code: SUMMER15
Description
Molnlycke Mepitel Safetac Transparent Wound Contact LayerMolnlycke Mepitel Safetac Transparent Wound Contact Layer Mepitel is a wound contact layer that can be left in place for up to 14 days depending on the condition of the wound. The long wear time of Mepitel reduces the necessity for frequent primary dressing changes. The porous structure of Mepitel allows exudate to pass into an outer absorbent dressing. The Safetac layer prevents the outer dressing from sticking to the wound and ensures atraumatic
Molnlycke Mepitel Safetac Transparent Wound Contact Layer
Mepitel is a wound-contact layer that can be left in place for up to 14 days depending on the condition of the wound. The long wear time of Mepitel reduces the necessity for frequent primary dressing changes. The porous structure of Mepitel allows exudate to pass into an outer absorbent dressing. The Safetac layer prevents the outer dressing from sticking to the wound and ensures atraumatic dressing changes. The Safetac layer seals around the wound edges and prevents exudate from leaking onto the surrounding skin, thus minimizing the risk of maceration.Benefits of Mepitel
- Minimizes pain and trauma at dressing changes
- May remain in place for up to 14 days which in turn ensures undisturbed wound healing
- Open mesh structure allows for application of topical agents and passage of exudate into secondary dressing
- Enables less frequent dressing changes
- Minimizes the risk of maceration
- Maintains product properties over time - leaves no residues and does not dry out
- Transparent for easy wound inspection during application and during wear
- Conforms well to body contours, promoting patient comfort during wear
- Stays in place; conforms well to body contours, may be cut
- Low potential for skin irritation and allergy
Areas of use:- Mepitel is designed for a wide range of wounds such as skin tears, skin abrasions, surgical incisions, second degree burns, blisters, lacerations, partial and full thickness grafts, diabetic ulcers, and venous and arterial ulcers.
Shipping Notes
- Free Standard Shipping on $100+ Orders to the USA.
- Except Preorder products are shipped in 48 hours.
- Delivery to the USA:
- Standard Shipping : 3-10 business days
- If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
- We offer a 30-day return/exchange service after receiving.
- Final sale items are not eligible for returns or exchanges.
- To process your return/exchange, please contact us at [email protected]
- Please click here for more details>>> Return & Exchange Policy
4.2 ★★★★★
Based on 23 reviews
Sort
Product Reviews
★★★★★ 5
If pump doesn't seem to work
Size: For 85-300 HP, Size: For 85-300 HP
Hi....I apologize it took me a while to get back to you with my results. Here is what I discovered about the pump and will also apply to some of the other comments I read in the reviews with people not getting the pump to work:
1.) I removed the pump to check the proper direction of the impeller and it was correct as can be seen in the photo.
2.) I built a pump shaft attachement so that I could operate the pump with a power drill.
3.) I attached the water muff to the unit and tried to pump water.....it wouldn't do so. What I did see however was that even at high hose discharge and small leakage at the muff I could not fill the water cavity in the housing.
4.) I installed a strap around the muff and tightened it very tight and THEN at high hose pressure I was able to get the cavity to fill with water.
5.) At that point I activated the drill and was able to get the pump to actually pump water. I then removed the pump housing and removed the O-Ring that resides on top of the impeller, reassembled and it would not pump water. Since the O-Ring sits higher than the original does I wanted to make sure that it was necessary to have it in the pump.
6.) I reassembled the engine and kept the tight strap on the bottom and finally it pumped water into the engine.
My conclusion that you can reply to other buyers if they have a problem:
Do NOT underestimate 2 things....1.)the lack of ability of the pump to draw water up AND 2.)the fact that if the muff leaks it will NOT fill the cavity when common sense says it should. This was a 120hp Johnson. The engine bottom must be immersed fully or the muff must be very tight on the lower unit for the pump to function.
Please feel free to post this if you wish.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on August 12, 2024
★★★★★ 5
Exelente
Size: For 85-300 HP
Exelente
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 21, 2026
★★★★★ 5
Good as new
Size: Package Dimensions 6.02 x 4.02 x 2.05 inches
Fitment was great and works as it should. Good quality
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on March 19, 2025
★★★★★ 3
Incorrect motor listed. Far smaller impeller than what's in the 6 horse johnson.
Size: For 5.5HP 6HP 7.5HP
It seems to be of good quality. However it does not fit a 6 horse johnson as it states. Therefore it will not pump water or function for my purposes. It was a waste of money.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on October 15, 2025
★★★★★ 5
OE Quality Part
Worked perfectly. Everything needed is there.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 27, 2026