SKU: 46886962903

Zipwake Kit Box KBI600-S PRO für MFD/CAN/NMEA

Sale price$1735.53 Regular price$1928.37
Save 10%

Pay in installments of $482.09 with ShopPay, AfterPay and Klarna

Shipping Estimate
USA
  • USA
  • CAN

Ships within 48 hours · Estimated delivery Aug 5 - Aug 10

Promo Codes Available:

For Your Every Summer RSVP, with Code: SUMMER15

Description

Zipwake Kit Box KBI600-S PRO für MFD/CAN/NMEAZIPWAKE Serie S S PRO Das ZIPWAKE Trimmsystem Serie S ist die smarte Lsung fr Gleiter und Halbgleiter von 20 bis 50 Fu und Geschwindigkeiten bis 60 Knoten. Mit modernster 3D Gyro GPS Technologie sorgt es fr perfekte Trimmung, mehr Stabilitt und bis zu 20 % weniger Kraftstoffverbrauch vollautomatisch und blitzschnell. Highlights Automatische Trimmsteuerung & Stabilisierung Reaktionszeit nur 1,5 Sekunden (S Serie) 0,3 Sekunden (S PRO) Weniger Rollen,

ZIPWAKE Serie S / S-PRO

Das ZIPWAKE Trimmsystem Serie S ist die smarte Lösung für Gleiter und Halbgleiter von 20 bis 50 Fuß und Geschwindigkeiten bis 60 Knoten. Mit modernster 3D Gyro-GPS-Technologie sorgt es für perfekte Trimmung, mehr Stabilität und bis zu 20 % weniger Kraftstoffverbrauch – vollautomatisch und blitzschnell.

Highlights

  • Automatische Trimmsteuerung & Stabilisierung

  • Reaktionszeit nur 1,5 Sekunden (S-Serie) / 0,3 Sekunden (S-PRO)

  • Weniger Rollen, schnelleres Gleiten, präzisere Kurven

  • Bis zu 20 % Kraftstoffersparnis

  • Wake Shaping Funktion (S-PRO) für perfekte Heckwellen beim Wakesurfen

  • Einfache Bedienung per Controller oder Integration ins Bordnetz (NMEA2000, CAN-BUS, WLAN, App)

Funktionen im Überblick

  • Active Pitch Control: optimaler Fahrwinkel für bessere Beschleunigung & Sicht

  • Active Roll Control: sofortige Stabilisierung bei Wind, Wellen & Beladung

  • Active Curve Control: dynamische Balance für sichere Kurvenfahrten

  • Wake Shaping (S-PRO): perfekte Welle für Wakeboard & Wakesurf

Flexibel & passgenau

  • 25 verschiedene Interceptoren für alle Bootstypen & Heckspiegelformen

  • Kit Boxen für schnellen Einbau – sofort startklar

  • Wahl zwischen Serie S und Serie S-PRO – abgestimmt auf Größe & Leistung Ihres Bootes

Zipwake Standard oder PRO

Zipwake Systeme git es als Standard- oder Pro-Version. Die PRO Versionen bieten eine deutlich schnellere Reaktionszeit der Interceptoren und zusätzliche Funktionen, wie z.B. Wake Shaping. Mit einer Geschwindigkeit von 0 auf 30mm (Serie S) in nur 0,3 Sekunden ermöglicht die erhöhte Blattgeschwindigkeit ultraschnelle Anpassungen an sich ändernde Bedingungen. Die genauen unterschiede finden Sie in der Produktbeschreibung.

Zipwake Erweiterung

Passen Sie das Basissystem (2 Interceptoren) an die technischen Gegebenheiten Ihre Bootes an. Sie können jedes Basissystem mit weiteren Interceptoren erweitern und verbessern damit die Wirkungsweise des Systems. Zur Auswahl der richtigen Interceptoren lesen Sie die Produktbeschreibung. 

Zipwake PRO Upgrade

Sie nutzen bereits ein Zipwake System? Mit den Upgrade Systemen können Sie schnell und einfach auf die neue PRO Version upgraden. Zipwake Upgrade Pakete finden Sie hier im Webshop.

Mit ZIPWAKE erleben Sie mehr Fahrspaß, Komfort und Sicherheit – und sparen gleichzeitig Kraftstoff. Perfekt für alle, die ihr Boot smarter und leistungsfähiger machen wollen.

Für mehr Informationen und zur Auswahl des richtigen Zipwake Systems lesen Sie die Produktbeschreibung oder informieren Sie sich unter www.zipwake.com


Lieferumfang

1 x IM (2012241) Integrator Module
1 x SC7-M12 (2011257) M12 Anschlusskabel 7 Meter
1 x DU-PRO (2022033) Distribution Unit PRO mit Stromkabel 4 Meter
2 x IT600-S PRO (2021234) Interceptor 600 S PRO mit Anschlusskabel 3 Meter, Kabelkanal

Shipping Notes
  • Free Standard Shipping on $100+ Orders to the USA.
  • Except Preorder products are shipped in 48 hours.
  • Delivery to the USA:
  1. Standard Shipping : 3-10 business days
  • If time is of the essence, please consider selecting expedited delivery for faster service.
Exchange/Return Notes
  • We offer a 30-day return/exchange service after receiving.
  • Final sale items are not eligible for returns or exchanges.
  • To process your return/exchange, please contact us at [email protected]
  • Please click here for more details>>> Return & Exchange Policy
SKU: 46886962903

Discover Niche Categories That Outsell

Top-Converting Item to Boost Your Average Order

4.7 ★★★★★
Based on 19 reviews
Sort
Highest Rating
Newest First
Oldest First
Product Reviews
S
Verified Purchase
Steve M.
Boise, US
★★★★★ 5
Works well. You need to drill a 3/8” hole
Appears to be well made, alignment bar slides in nicely. As stated, you need to drill a hole in the bar for the gimble bearing driver, the directions are not clear, what I did was before I take out the old gimble bearing, put an O ring on the bar close to the last step on the bar, slide the bar all the way in, then carefully slide the bar out, this marks the distance from the back of the gimble bearing to where the shaft on the outdrive bottoms out, move the O ring a 1/4” towards the stepped part of the alignment tool (this is so you won’t bottom out the alignment tool when driving the gimble bearing in) then slide the driver puck up to the O ring and use a 3/8” diameter transfer punch through the side hole in the puck to mark the bar. You need to drill a 3/8” diameter hole in the alignment bar, two V blocks, some clamps, and a drill press will make drilling much easier, after the bar is securely mounted and centered in the drill press, use a center drill, then 1/4” drill first, using plenty of oil, drill all the way through, then use the 3/8” drill, deburr both sides and you should be good to go. People complain that it doesn’t come pre-drilled, the reason is that not all out drives are the same so you have to fit it to the outdrive that you have. Fortunately, I have a machine shop at my house and have a jig setup with various drill bushings, but the method I described above should work for you. Just make sure you’re perfectly centered and secure before you start drilling.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2026
N
Verified Purchase
Nancy filippi
Charlottesville, US
★★★★★ 5
A must pull your gimbal bearing
You do need to drill a hole but worked perfect
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on December 26, 2025
R
Verified Purchase
rich911s
Fort Morgan, US
★★★★★ 5
Worked for Volvo Penta SX Gimbal Bearing
Very heavy tool, I was surprised. Pulled my bearing like it was nothing. Putting the new bearing in was a little more difficult as you have to drill a hole in the engine alignment shaft where it will work for your particular outdrive. Not hard, but it does not come pre-drilled as the required depth for each particular gimbal bearing differs by manufacturer and model. Measure your bearing placement before removal and check that it was installed correctly in the first place. The bearing should line up with the grease fitting and the o-rings on the drive shaft should end up riding in the middle of the bearing. once you have your measurement drill the hole, I used a drill press. I suppose you could use it on multiple outdrive models as long as you can drill more holes.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on June 5, 2023
G
Verified Purchase
Greg
Waukegan, US
★★★★★ 5
Great value
This kit worked perfectly on my Alpha one mercury outdrive. I saw a lot of people mention that it was a hassle to drill the hole when you better have all this alignment stuff. I threw it in use my regular drill drill guide and then the second hole was lined up. Pulling Gimble be very easy. I did have to adjust it up at an angle because my bearing was sitting in their crooked and it came out the second time I made the adjustment to the angle. I would highly recommend this.
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on April 16, 2024
T
Verified Purchase
Tommy Knapp
Lake Worth, US
★★★★★ 1
Unfinished product - doesn't work - waste of money
in order to use this as an installation tool the directions tell you to drill a hole through the 2 inch steel rod..... either this hole should already be drilled, or this should not be advertised as an installation tool..... it will not install any bearings without extensive modification and requires the use of a drill press or a lathe. very dissatisfied that I now have to buy ANOTHER tool just to finish this job because this one doesn't do what it's described to do.... piece of junk... typical amazon garbage.... this is why I haven't used amazon in over a year... they rip you off with garbage.... I should have known better .... don't buy this junk .... Now they say 20 -30 days to get my refund .... Don't waste your time
WAS THIS REVIEW HELPFUL?YesReportShare
Reviewed in the United States on May 26, 2026

recommand products